VNQ7050AJTR
Product Specifications
VNQ7050AJTR — Integrated Motor Driver / Smart Power Switch by STMicroelectronics
The VNQ7050AJTR is an STMicroelectronics integrated motor driver / smart power switch in PowerSSO-16 for automotive and industrial actuator control applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| VNQ7050AJTR | Full Part Number | STMicroelectronics Motor Driver / Power Switch |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | VNQ7050AJTR |
| Package | PowerSSO-16 |
| Type | Integrated Motor Driver / Smart Power Switch |
| Qualification | Automotive AEC-Q100 / Industrial |
Product Overview
The VNQ7050AJTR is an STMicroelectronics integrated motor driver / smart power switch in PowerSSO-16 package. Featuring ST's VIPower technology with monolithic integration of power MOSFETs, gate drivers, and protection/diagnostic circuitry, it simplifies motor control and high-side/low-side switching designs with reduced BOM count and enhanced reliability.
Key Features & Benefits
VIPower Monolithic Integration — Power + Control in One Package
ST's VIPower technology integrates N-channel power MOSFETs, gate drivers, charge pump, and comprehensive protection circuitry on a single die — eliminating external MOSFETs, bootstrap diodes, and sense resistors.
Comprehensive Protection & Diagnostics
Built-in overcurrent, overtemperature (thermal shutdown), undervoltage lockout, and load-dump protection with diagnostic feedback (current sense output, fault status flag) enables self-protecting designs suitable for safety-critical and autonomous systems.
Automotive-Grade Robustness
Designed to withstand harsh automotive and industrial environments including load dump, reverse battery, and extended temperature range for reliable operation in drone payload systems, robotics, and vehicle applications.
Target Applications
Drone Payload & Actuator Control
Drives brushed DC motors, solenoids, and resistive/inductive loads in drone gimbal systems, payload release mechanisms, landing gear actuators, and auxiliary power switching.
Automotive Body & Powertrain
Targets automotive applications including throttle control, EGR valves, HVAC actuators, mirror folding, headlamp leveling, and relay/lamp drivers — all requiring AEC-Q100 qualification.
Industrial Automation & Robotics
Powers motor control, valve actuation, and power distribution in industrial robots, conveyor systems, automated guided vehicles (AGVs), and factory automation equipment.
Frequently Asked Questions
What protection features does the VNQ7050AJTR include?
The VNQ7050AJTR features overcurrent protection, overtemperature shutdown, undervoltage lockout, and diagnostic feedback — ensuring robust, self-protecting operation in demanding environments.
Is external current sensing required?
No. The integrated current-sense output provides proportional load current feedback, eliminating the need for external shunt resistors and differential amplifiers.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics VNQ7050AJTR with full traceability and batch-level QA documentation. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.
VNQ7050AJTR: four high side channels at 50 milliohms for automotive loads
VNQ7050AJTR is a quad channel high side driver from STMicroelectronics in the PowerSSO-16 body, tape and reel. It runs from 4 V to 28 V with a 40 V maximum transient supply, has a typical on state resistance of 50 milliohms per channel, limits current at about 27 A, and draws 0.5 microamps in standby. It is automotive qualified and built in VIPower M0-7 technology, and it is aimed at signal lamps, LED rear combinations and other resistive, inductive and capacitive loads in a vehicle.
Each channel has a current sense output that mirrors the load current with high precision, and the diagnostics go further than a simple fault flag: overload and short to ground are reported as power limitation, thermal shutdown is reported separately, an open load is detected in the off state, and a short to supply is detected as well. The fault behaviour is configurable, including a latch off on overtemperature or power limitation with a dedicated reset pin.
Vendor figures for this code
| Channels | Four high side drivers with current sense feedback |
| Operating voltage | 4 V to 28 V |
| Maximum transient supply | 40 V |
| On state resistance | 50 milliohms typical per channel |
| Current limitation | 27 A typical |
| Standby current | 0.5 microamps maximum |
| Input compatibility | 3 V and 5 V CMOS |
| Diagnostics | Analog current mirror, overload and short to ground, thermal shutdown, off state open load, short to supply, sense enable |
| Fault handling | Configurable latch off with a dedicated reset pin |
| Other protections | Loss of ground, loss of supply, reverse battery with external components, electrostatic discharge |
| Package | PowerSSO-16 |
| Qualification | Automotive |
Why the standby figure is the headline for a body controller
A parked vehicle still drains its battery through the modules that stay connected. Half a microamp per driver across a dozen modules is nothing, while a milliamp per driver across the same dozen is a dead battery after a few weeks of parking. That is why the standby current is specified as a maximum and printed next to the on resistance rather than buried in a table, and it is the number a body controller specification is written against.
The reverse battery protection deserves a note because the vendor qualifies it with external components. The part survives a reversed connection when the external network the datasheet shows is present, and it does not survive it on its own. A build that expects the driver to protect itself without those parts will fail the reverse polarity test, and the fix is in the circuit rather than in the part.
Use, and the pages that follow on
Typical loads are signal lamps up to 27 W, LED rear combinations, relays, and small motors in a body controller. Related pages are power management cross reference, component traceability report for the automotive chain of custody, and PPAP submission checklist for the approval file.
Questions buyers ask on this code
Whether the four channels can drive four 27 W lamps at once is the first, and the current limit is per channel while the package has one thermal limit that four loaded channels will reach together. The second is the open load detection, which works in the off state and is what a lamp failure warning depends on. The third is the latch behaviour, which has to be chosen deliberately: a latched channel stays off until the reset pin is driven, and a product that expects the lamp to come back on its own after a thermal event will not get that behaviour from a latched build.