VND7NV04TR-E
Product Specifications
VND7NV04TR-E — Integrated Motor Driver / Smart Power Switch by STMicroelectronics
The VND7NV04TR-E is an STMicroelectronics integrated motor driver / smart power switch in TO-252-2(DPAK) for automotive and industrial actuator control applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| VND7NV04TR-E | Full Part Number | STMicroelectronics Motor Driver / Power Switch |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | VND7NV04TR-E |
| Package | TO-252-2(DPAK) |
| Type | Integrated Motor Driver / Smart Power Switch |
| Qualification | Automotive AEC-Q100 / Industrial |
Product Overview
The VND7NV04TR-E is an STMicroelectronics integrated motor driver / smart power switch in TO-252-2(DPAK) package. Featuring ST's VIPower technology with monolithic integration of power MOSFETs, gate drivers, and protection/diagnostic circuitry, it simplifies motor control and high-side/low-side switching designs with reduced BOM count and enhanced reliability.
Key Features & Benefits
VIPower Monolithic Integration — Power + Control in One Package
ST's VIPower technology integrates N-channel power MOSFETs, gate drivers, charge pump, and comprehensive protection circuitry on a single die — eliminating external MOSFETs, bootstrap diodes, and sense resistors.
Comprehensive Protection & Diagnostics
Built-in overcurrent, overtemperature (thermal shutdown), undervoltage lockout, and load-dump protection with diagnostic feedback (current sense output, fault status flag) enables self-protecting designs suitable for safety-critical and autonomous systems.
Automotive-Grade Robustness
Designed to withstand harsh automotive and industrial environments including load dump, reverse battery, and extended temperature range for reliable operation in drone payload systems, robotics, and vehicle applications.
Target Applications
Drone Payload & Actuator Control
Drives brushed DC motors, solenoids, and resistive/inductive loads in drone gimbal systems, payload release mechanisms, landing gear actuators, and auxiliary power switching.
Automotive Body & Powertrain
Targets automotive applications including throttle control, EGR valves, HVAC actuators, mirror folding, headlamp leveling, and relay/lamp drivers — all requiring AEC-Q100 qualification.
Industrial Automation & Robotics
Powers motor control, valve actuation, and power distribution in industrial robots, conveyor systems, automated guided vehicles (AGVs), and factory automation equipment.
Frequently Asked Questions
What protection features does the VND7NV04TR-E include?
The VND7NV04TR-E features overcurrent protection, overtemperature shutdown, undervoltage lockout, and diagnostic feedback — ensuring robust, self-protecting operation in demanding environments.
Is external current sensing required?
No. The integrated current-sense output provides proportional load current feedback, eliminating the need for external shunt resistors and differential amplifiers.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics VND7NV04TR-E with full traceability and batch-level QA documentation. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.
VND7NV04TR-E: a 60 milliohm OMNIFET in the DPAK body
VND7NV04TR-E is a single OMNIFET II protected power MOSFET in the DPAK body, on tape and reel. It holds 60 milliohm on resistance, a 6 A typical current limit and a 40 V clamp. Thermal shutdown, linear current limitation, short circuit protection and an integrated clamp are all on the die, and the fault is reported back through the input pin.
The string sits between the 35 milliohm member and the 250 milliohm SO-8 members of the same family. That middle position is useful for loads of 3 A to 6 A, where the 35 milliohm part is more copper than the load needs and the small outline parts are too small to hold the heat.
Figures come from the VNN7NV04 and VND7NV04 data sheet read this round, which prints 60 milliohm, 6 A current limit and a 40 V clamp for the family and lists the D package as the DPAK body.
The switch in numbers
| Function | Single fully protected power MOSFET, OMNIFET II, low side |
| On resistance | 60 milliohm |
| Current limit | 6 A typical, linear |
| Clamp voltage | 40 V drain to source |
| Protections | Thermal shutdown, short circuit, integrated clamp, ESD |
| Fault feedback | Through the input pin voltage |
| Driving mode | Direct gate access, analog driving possible |
| Switching use | DC up to 50 kHz |
| Compatibility | Behaviour compatible with standard power MOSFETs |
| Package | DPAK, tab down for board cooling |
| Packing | Tape and reel for the TR string |
Loss at 60 milliohm
At 60 milliohm, 3 A costs 0.54 W and 6 A costs 2.16 W. The DPAK tab spreads that into the copper, and at 3 A the part runs without a heatsink on a reasonable board. At 6 A the loss is above two watts, which the tab can hold only with a copper area sized for it, and that is where the DPAK is chosen over the SO-8 members of the family.
The linear limitation is the family behaviour: under a short the current is held at the limit while the die heats, and thermal shutdown cycles the channel until the fault clears. The switch is protected against the event, and it is not a fast electronic fuse.
Where it fits
Relay and solenoid drive at a few amps, lamp and heater switching, and small motor drive in one direction on a 12 V or 24 V rail inside the 40 V clamp. Automotive body modules, industrial control boards and appliance power boards are the usual homes for this body size.
A customer moving from an SO-8 OMNIFET string to this DPAK part gains thermal headroom and loses board area. The move in the other direction is the one to review, because the loss at the same current does not change but the ability to remove it does.
We supply the string and hold the date code record for each lot. Our power management cross reference page lists the family by resistance and package, the date code management page describes how older stock is kept away from a line with a shelf life rule, and the incoming inspection plan page covers the goods in checks.
Three questions buyers ask about this string
Is the 6 A limit a continuous rating? No. It is the typical linear current limit under a fault. Continuous current follows from the 60 milliohm loss and the copper under the tab.
Can the tab be left unconnected? It can be soldered to a small pad, but then the thermal path is the package only and the continuous current falls sharply.
Does it need a freewheel diode for a coil? The clamp covers the kick within its energy capability, and an external diode is worth adding for a large coil switched often.