ST1S14PHR
Product Specifications
ST1S14PHR — Voltage Regulator by STMicroelectronics
The ST1S14PHR is an STMicroelectronics voltage regulator in HSOP-8 for reliable power management in embedded and industrial applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| ST1S14PHR | Full Part Number | STMicroelectronics Voltage Regulator |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | ST1S14PHR |
| Package | HSOP-8 |
| Type | Fixed/Adjustable Voltage Regulator |
| Qualification | Industrial (-40°C to +125°C) |
Product Overview
The ST1S14PHR is an STMicroelectronics voltage regulator in HSOP-8 package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.
Key Features & Benefits
Stable Output with Built-in Protection
Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.
Wide Compatibility & Minimal External Components
Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.
Industrial Temperature Range
Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.
Target Applications
Drone & Embedded System Power Rails
Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.
Industrial & Automotive Electronics
Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.
General-Purpose Point-of-Load Regulation
Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.
Frequently Asked Questions
What is the output voltage of the ST1S14PHR?
Check the specific variant. The ST1S14PHR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.
What capacitors are needed for stability?
Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics ST1S14PHR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.
ST1S14PHR: 3 A at 850 kHz from an input that reaches 48 V
ST1S14PHR is a step down switching regulator from STMicroelectronics in the HSOP8 body with an exposed pad, tape and reel. It carries 3 A of DC output current, takes an input from 5.5 V to 48 V, sets the output from 1.22 V upward, and switches at a fixed 850 kHz. It was made for the industrial and printer end of the market, where a 24 V or 36 V rail has to come down to 5 V on a board that has no room for a controller plus two external switches.
The 48 V input is the reason to pick it over the ST1S10. The ST1S10 stops at 18 V, which rules out a 24 V industrial bus with any margin. This part takes the full 24 V rail and the 36 V battery rail of a forklift or a floor scrubber, with a 48 V ceiling that leaves room for the transient on a motor bus. The power good open collector output is the other addition: it tells the downstream logic that the rail is in regulation instead of leaving it to guess.
What the document states, and the one number that disagrees with itself
| Output current | 3 A DC |
| Input voltage | 5.5 V to 48 V |
| Output voltage | Adjustable from 1.22 V |
| Switching frequency | 850 kHz internally fixed |
| Switch on resistance | 250 milliohms typical per the feature list, 200 milliohms per the description |
| Quiescent current | 2 mA maximum over temperature |
| Compensation | Embedded, no external network |
| Power good | Open collector output |
| Protections | Internal current limit, pulse by pulse, current foldback, thermal shutdown |
| Light load | Zero load current operation |
| Other functions | Internal soft start, inhibit for zero consumption |
| Package | HSOP8 with exposed pad, about 40 degrees per watt |
The on resistance row needs a phone call, not a guess
The feature list and the descriptive text of the same datasheet print two values for the switch on resistance, 250 milliohms and 200 milliohms. Both are described as typical. On a 3 A rail the difference is 0.45 W of conduction loss in the switch, which is not a rounding error on a body that manages 40 degrees per watt. The honest position is to work the thermal budget at the higher figure and to treat the lower one as a benefit if the vendor confirms it in writing. This is exactly the kind of row that a purchase order should not be built on without a written answer.
The second number worth checking is the 2 mA quiescent current. It is a maximum over temperature, which means the part is not a sleep mode regulator. A product that has to hold a rail alive for months on a battery needs a part with microamps of standby, and this one is meant to be switched off when it is not needed.
Where it is used, and the related pages
Typical loads are industrial controllers, printers, DC to DC modules and high current LED drivers, all of them running from a 24 V or 36 V bus. Related pages are power management cross reference, pin to pin cross reference, and incoming inspection plan for the checks that catch a mis-marked reel of a part this widely copied.
Questions buyers ask on this code
Whether 48 V is a working voltage or a transient rating is the first, and it is the operating input range in the vendor table, so a 48 V bus that swings to 55 V is outside it. The second is the compensation, which is inside the part, so the output filter values are constrained by the vendor curve rather than free. The third is the exposed pad and the via field under it, which is the difference between a 3 A rail that runs cool and one that shuts down on a warm day.