Contact Us

VIPER26HDTR

Brand: ST
VIPER26HDTR is a switching regulator IC from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine VIPER26HDTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

VIPER26HDTR — Voltage Regulator by STMicroelectronics

The VIPER26HDTR is an STMicroelectronics voltage regulator in SO-16 for reliable power management in embedded and industrial applications.

Part Number Decoded — Field by Field

FieldValueMeaning
VIPER26HDTRFull Part NumberSTMicroelectronics Voltage Regulator

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberVIPER26HDTR
PackageSO-16
TypeFixed/Adjustable Voltage Regulator
QualificationIndustrial (-40°C to +125°C)

Product Overview

The VIPER26HDTR is an STMicroelectronics voltage regulator in SO-16 package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.

Key Features & Benefits

Stable Output with Built-in Protection

Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.

Wide Compatibility & Minimal External Components

Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.

Industrial Temperature Range

Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.

Target Applications

Drone & Embedded System Power Rails

Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.

Industrial & Automotive Electronics

Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.

General-Purpose Point-of-Load Regulation

Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.

Frequently Asked Questions

What is the output voltage of the VIPER26HDTR?

Check the specific variant. The VIPER26HDTR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.

What capacitors are needed for stability?

Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics VIPER26HDTR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.

VIPER26HDTR: an 800 V offline converter at 115 kHz with under 30 mW at no load

VIPER26HDTR is the H frequency member of the VIPER26 family from STMicroelectronics, in the SO16 narrow body. It integrates an 800 V avalanche rugged power MOSFET with a current mode PWM controller, starts itself from an embedded high voltage source, and carries an embedded error amplifier, so a complete isolated flyback needs little more than the transformer, the output diode and a handful of passive parts. The H suffix sets the switching frequency at 115 kHz plus or minus 8 kHz and the L suffix at 60 kHz plus or minus 4 kHz.

The two numbers that sell this part are the 800 V rating and the no-load consumption. Eight hundred volts leaves room for the leakage inductance spike on a 265 V AC input without a large snubber, and the vendor prints less than 30 mW at 230 V AC with no load and less than 400 mW at 230 V AC with a 250 mW load. Those two figures are what a standby budget is written against, and they are measured rather than estimated.

The vendor specification in one table

FunctionOffline converter with integrated 800 V avalanche rugged MOSFET
Switching frequency, H type115 kHz plus or minus 8 kHz, jittered
Switching frequency, L type60 kHz plus or minus 4 kHz, jittered
No load consumptionLess than 30 mW at 230 V AC
Consumption at 250 mW loadLess than 400 mW at 230 V AC
ControlCurrent mode PWM with embedded error amplifier
Start-upEmbedded high voltage start-up and sense FET
Current limitAdjustable set point
Soft startBuilt in, for a monotonic rise at power up
ProtectionsOverload and short circuit, feedback loop disconnection, hysteretic thermal shutdown, all with auto-restart
PackageSO16 narrow, also DIP-7 in the family
Named applicationsAppliance auxiliary supplies, power metering, LED drivers, set top box and recorder supplies

Why the jitter is there

The plus or minus 8 kHz spread around 115 kHz is deliberate. Spreading the switching energy over a band instead of concentrating it at one frequency reduces the peak of the conducted emission, which is what allows a smaller and cheaper EMI filter to pass the same limit. It does not change the efficiency in any meaningful way, and it does not change the transformer, which is still built around the centre frequency. An engineer who measures the switching waveform and sees it move should not treat that as a fault.

The 800 V rating is the other half of the EMI story. On a 265 V AC input the rectified rail sits near 375 V, and the leakage spike on the drain adds another 150 V to 250 V depending on the snubber. A 600 V device is at the edge of that arithmetic and needs a careful snubber, while an 800 V device leaves margin that can be spent on a smaller snubber or a tighter transformer. The trade is on-resistance, which rises with the voltage rating, and that is why the power level of this family stops where it does.

Where it is used, and the pages that follow on

Typical loads are appliance auxiliary supplies, metering supplies, LED drivers and the standby rail of a set top box. In SUPERB builds the part turns up on the mains side of industrial instruments and on power metering boards. Related pages are power management cross reference, obsolete part cross reference hub when a supply is moved off a discontinued offline switcher, and one stop BOM sourcing.

Questions buyers ask on this code

The first is which frequency to order, and the answer depends on the transformer size and the EMI filter: the H type at 115 kHz allows a smaller transformer and needs a better filter, the L type does the opposite. The second is whether the part needs an auxiliary winding, and the embedded start-up source means the supply can start without one, though most builds still use a winding to cut the no-load loss further. The third is the auto-restart behaviour on a fault, which suits a consumer product and does not suit a product that must latch off for safety.