L78L05ACUTR
Product Specifications
L78L05ACUTR — Voltage Regulator by STMicroelectronics
The L78L05ACUTR is an STMicroelectronics voltage regulator in SOT-89(SOT-89-3) for reliable power management in embedded and industrial applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| L78L05ACUTR | Full Part Number | STMicroelectronics Voltage Regulator |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | L78L05ACUTR |
| Package | SOT-89(SOT-89-3) |
| Type | Fixed/Adjustable Voltage Regulator |
| Qualification | Industrial (-40°C to +125°C) |
Product Overview
The L78L05ACUTR is an STMicroelectronics voltage regulator in SOT-89(SOT-89-3) package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.
Key Features & Benefits
Stable Output with Built-in Protection
Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.
Wide Compatibility & Minimal External Components
Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.
Industrial Temperature Range
Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.
Target Applications
Drone & Embedded System Power Rails
Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.
Industrial & Automotive Electronics
Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.
General-Purpose Point-of-Load Regulation
Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.
Frequently Asked Questions
What is the output voltage of the L78L05ACUTR?
Check the specific variant. The L78L05ACUTR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.
What capacitors are needed for stability?
Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics L78L05ACUTR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.
L78L05ACUTR: the 5 V L78L with the wide C band, and where that band is good enough
L78L05ACUTR is the 5 V member of the L78L family in the C grade, SOT-89, tape and reel. Its output window is plus or minus 8 percent, which at 5 V is 4.6 to 5.4 V, and it is specified from 0 to 125 degrees junction. It is the cheapest way to make a quiet 5 V rail at up to 100 mA, and it is the version most often found on boards that were cost reduced after the first prototype.
The C band is wide, but it is not a defect. A 5 V rail that feeds a display, a relay driver, an LED string or a cooling fan does not care whether it sits at 4.75 V or 5.2 V. A rail that feeds an ADC reference or a precision sensor bridge does care, and that is the point at which the A grade or a different regulator has to be chosen. Getting this decision right at the BOM stage is cheaper than discovering it at the EMC test house.
What the C grade table says
| Output voltage at 25 degrees | 4.6 to 5.4 V, plus or minus 8 percent |
| Output voltage, 1 to 40 mA | 4.5 to 5.5 V over an input of 7 to 20 V |
| Output current | 100 mA with adequate heat sinking |
| Maximum input | 30 V for the 3.3 to 9 V members |
| Dropout voltage | 2 V typical at 40 mA |
| Quiescent current | 6 mA maximum at 25 degrees, 5.5 mA at 125 degrees |
| Quiescent current change | 0.2 mA, 1 to 40 mA |
| Line regulation | 200 mV maximum, 8.5 to 20 V |
| Load regulation | 150 mV maximum, 1 to 100 mA |
| Supply voltage rejection | 49 dB typical at 120 Hz |
| Output noise | 40 microvolts typical, 10 Hz to 100 kHz |
| Package | SOT-89, tape and reel |
| Junction range, C grade | 0 to 125 degrees |
The 0 to 125 degree rating is a real limit
The C grade is not specified below freezing. On an indoor board that is irrelevant, and on an outdoor unit, a cold chamber test or a vehicle it is the deciding line. The AB grade of the same voltage is specified from minus 40 degrees and carries the tighter band, so a product that has to start at minus 20 degrees cannot use this code no matter how the rest of the circuit is arranged. This is one of the few places where a part number change is the whole fix.
The 2 V dropout rule applies here exactly as on the A grade. From a 7 V input the part holds 5 V at 40 mA, from a 6.5 V input it does not, and a 9 V battery that has run down to 6.8 V will drag the output with it. Boards that run from a battery usually put a switching stage in front of this part for that reason.
Use and the related pages
Common loads are relay drivers, small fans, LED strings and the logic supply of a module that has its own internal regulator. In SUPERB builds the part also appears as the analogue 5 V rail on converter boards, where its 49 dB of rejection at 120 Hz is enough to keep the mains ripple off a low level signal. Related pages are power management cross reference, how to reduce component cost for the grade question, and one stop BOM sourcing.
Questions buyers ask on this code
The first is whether the C grade can replace the A grade already on the drawing. Electrically it fits the footprint, but the guarantee changes on both voltage and temperature, so the substitution needs a written check against the load window. The second is the reel and the package, since the U suffix is SOT-89 and the SOT-89 pin order differs from the SO-8. The third is counterfeit exposure on a part this common, which is why the date code and the traceability record matter more here than on an exotic device.