Contact Us

L99MC6TR

Brand: ST
L99MC6TR is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine L99MC6TR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

L99MC6TR — Power MOSFET / Motor Driver by STMicroelectronics

The L99MC6TR is an STMicroelectronics power mosfet / motor driver in N/A. Supplied by SUPERB Automation with verified sourcing.

Part Number Decoded — Field by Field

FieldValueMeaning
L99MC6TRFull Part NumberSTMicroelectronics Power MOSFET / Motor Driver

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberL99MC6TR
PackageN/A
CategoryPower MOSFET / Motor Driver
QualificationIndustrial / Automotive

Product Overview

The L99MC6TR is an STMicroelectronics power mosfet / motor driver in N/A package. Engineered with ST's proven semiconductor technology and quality manufacturing processes, it delivers reliable performance for a wide range of electronic applications. Supplied by SUPERB Automation with full traceability and competitive lead times.

Key Features & Benefits

STMicroelectronics Quality & Reliability

Backed by ST's rigorous qualification testing, statistical process control, and decades of semiconductor manufacturing excellence — ensuring consistent, reliable performance across production batches.

Industrial Temperature Range

Designed for reliable operation across industrial temperature ranges, suitable for outdoor, automotive, and factory-floor environments where temperature extremes challenge lesser components.

Global Availability via SUPERB Automation

SUPERB Automation maintains verified supply channels for genuine STMicroelectronics components, with competitive pricing and lead times from prototype quantities to full production volumes.

Target Applications

Embedded & IoT Systems

Integrates into microcontroller-based designs, sensor interfaces, and IoT endpoints requiring reliable electronic components from a trusted manufacturer.

Industrial Control & Automation

Suitable for industrial PLCs, motor drives, sensor transmitters, and factory automation equipment demanding components with proven field reliability.

Consumer & Automotive Electronics

Used in consumer devices, automotive subsystems, and general electronic designs benefiting from ST's broad product portfolio and manufacturing scale.

Frequently Asked Questions

Where can I find the datasheet for L99MC6TR?

The official datasheet is available on STMicroelectronics' website (st.com). SUPERB Automation can also provide documentation and application support upon request.

Is this part in stock and available?

SUPERB Automation supplies genuine STMicroelectronics L99MC6TR through verified sourcing channels. Contact us with your target quantity and timeline for current availability and pricing.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with flexible packaging options (tray, cut tape, or full reel).

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics L99MC6TR with full traceability and batch-level QA documentation. Whether you need prototype quantities or production volumes, we source through verified channels with competitive lead times. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.

L99MC6TR: six configurable channels with an SPI interface

L99MC6TR is a six channel output driver in the PowerSSO-16 body, on tape and reel. Three of the channels are self configuring, so each can act as a high side or a low side driver, and three are dedicated low side channels. The on resistance is 0.7 ohm typical at 25 degrees, each output limits at a minimum of 0.6 A, and a 16 bit SPI interface controls the outputs and reads back the diagnostics.

The configurable channels are what make the part interesting for a module with a mixed load list. A high side channel drives a lamp to ground, a low side channel drives a relay coil from the battery, and a pair of channels forms a half bridge for a small motor in one direction with cross current protection. The same package covers all three cases, and the configuration comes from the SPI register rather than from a different order code.

Figures come from Doc ID 16523 Rev 2, dated September 2013, read this round.

The channels and the interface

FunctionSix channel configurable driver, three self configuring and three low side
On resistance0.7 ohm typical at 25 degrees
Current limitMinimum 0.6 A on each output
ConfigurationEach of the first three channels can be high side or low side
ModesPWM direct mode, bulb mode with recovery, LED mode with slew rate control, bridge mode with cross current protection
Direct controlChannel 2 can be driven from the input pin for PWM
Interface16 bit SPI for control and diagnostics
DiagnosticsNormal operation, open load in off state, overcurrent, temperature warning, overtemperature
ProtectionsOvertemperature and short circuit on every output, internal clamp diodes
Supply range3.0 V to 5.25 V on the logic supply
Standby current5 microamp typical
Low voltage behaviourHigh side switches operate down to a 3 V crank voltage
PackagePowerSSO-16

Loss at 0.7 ohm and the 0.6 A limit

At 0.7 ohm, 0.3 A costs 0.063 W and 0.6 A costs 0.252 W per channel. Six channels at the limit would be 1.5 W in one package, which is inside what a PowerSSO-16 can hold with a copper area, so the thermal side of this part is comfortable when every channel sits at its limit. The limit itself is the constraint: this is a driver for lamps, relays, LEDs and mirror motors, not for a load that draws amps.

The bulb mode with recovery is the feature that matters for incandescent loads. A cold filament draws a multiple of its hot current, the channel limits, and the recovery behaviour brings the output back once the filament warms. Without that mode a bulb looks like a short at switch on and the channel stays in limitation.

The half bridge configuration and cross current

Two configurable channels can form a half bridge, and the cross current protection stops both from conducting at once during a direction change. That protection is a hardware function, which means the SPI command sequence cannot create a shoot through even if the controller writes both bits in the same frame. For a mirror motor or a small actuator that reverses, the arrangement removes two discrete drivers and their dead time control.

The LED mode with slew rate control is there for EMC. A fast edge on a long lamp harness radiates, and slowing the edge costs a little switching loss in exchange for a quieter harness. On a body module that has to pass a radiated emissions test, that register setting is often the difference between a pass and a filter.

Where the part is used

Relay, LED, motor and mirror adjustment drivers in automotive body modules, and anything that needs several small outputs with diagnostics behind one SPI port. The 3 V crank operation matters on a vehicle that has to keep its outputs alive during a start event.

We supply the string and compare it with discrete protected switches when a module needs fewer than six outputs. The power management cross reference page lists the multi channel drivers we hold, the PPAP submission checklist page covers the automotive submission, and the PCBA test coverage strategy page describes how an SPI driven output block is tested at assembly.

Three questions buyers ask about this string

Is the 0.6 A limit per output? Yes. Each output limits at a minimum of 0.6 A, and the six channels are independent.

Can the SPI be shared with other devices? It is a standard 16 bit interface with a chip select, so it shares a bus in the usual way, with the diagnostics read back per frame.

Does the part need external clamp diodes? Internal clamp diodes are integrated. An external diode is still useful on a load with a large inductive kick that would otherwise heat the die.