VIPER12ADIP-E
Product Specifications
VIPER12ADIP-E — Voltage Regulator by STMicroelectronics
The VIPER12ADIP-E is an STMicroelectronics voltage regulator in DIP-8 for reliable power management in embedded and industrial applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| VIPER12ADIP-E | Full Part Number | STMicroelectronics Voltage Regulator |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | VIPER12ADIP-E |
| Package | DIP-8 |
| Type | Fixed/Adjustable Voltage Regulator |
| Qualification | Industrial (-40°C to +125°C) |
Product Overview
The VIPER12ADIP-E is an STMicroelectronics voltage regulator in DIP-8 package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.
Key Features & Benefits
Stable Output with Built-in Protection
Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.
Wide Compatibility & Minimal External Components
Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.
Industrial Temperature Range
Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.
Target Applications
Drone & Embedded System Power Rails
Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.
Industrial & Automotive Electronics
Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.
General-Purpose Point-of-Load Regulation
Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.
Frequently Asked Questions
What is the output voltage of the VIPER12ADIP-E?
Check the specific variant. The VIPER12ADIP-E is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.
What capacitors are needed for stability?
Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics VIPER12ADIP-E with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.
VIPER12ADIP-E: an offline switcher in a DIP-8 body
VIPER12ADIP-E is a low power offline switching regulator in the DIP-8 body. It combines a current mode PWM controller with a high voltage power MOSFET on one chip, switches at a fixed 60 kHz, and runs from a supply pin range of 9 V to 38 V with a high voltage start up current source that charges that pin from the rectified mains. Typical power capability is 13 W on a European 195 V to 265 V AC input and 8 W across the wide 85 V to 265 V AC range.
The DIP-8 body is the reason this string exists alongside the SO-8 version. The through hole package spreads heat into the board and the pins, and the 13 W figure at the narrow mains range is five watts more than the same die in the small outline body. For a 10 W standby supply the choice of body decides whether the part runs cool or cycles on thermal shutdown.
Figures come from the VIPER12A-E data sheet read this round, which prints the 60 kHz fixed frequency, the 9 V to 38 V supply pin range, the 13 W and 8 W capability figures and the auto restart protection set.
The device in numbers
| Function | Offline PWM controller with integrated high voltage power MOSFET |
| Switching frequency | 60 kHz fixed |
| Supply pin range | 9 V to 38 V |
| Start up | High voltage start up current source from the drain |
| Capability, European mains | 13 W in DIP-8, 8 W in SO-8, 195 V to 265 V AC |
| Capability, wide mains | 8 W in DIP-8, 5 W in SO-8, 85 V to 265 V AC |
| Control | Current mode with an internal sense FET |
| Light load | Automatic burst mode |
| Undervoltage | Auxiliary undervoltage lockout with hysteresis |
| Protections | Overtemperature, overcurrent, overvoltage, all with auto restart |
| Overvoltage behaviour | Hiccup mode |
| Package | DIP-8 |
Why the body changes the power rating
The two capability figures are not marketing. A flyback built around this part dissipates most of its heat in the integrated switch and in the snubber, and the DIP-8 body has a thermal path through eight pins and the plastic to the board. In the small outline body the same loss raises the junction further, so the guaranteed capability drops from 13 W to 8 W on the narrow mains range and from 8 W to 5 W on the wide range.
That is the arithmetic a customer needs before changing body to save area. A build that runs at 10 W on 230 V AC is inside the DIP-8 figure and outside the SO-8 figure, and the failure mode is a thermal shutdown that appears only in a warm enclosure.
The start up path and the auxiliary winding
The internal current source charges the supply capacitor from the drain at power up, then the auxiliary winding takes over once the converter is switching. The value of that capacitor and the turn ratio of the auxiliary winding decide the start time and the point at which the controller drops out under load. A build that starts reliably at 25 degrees can fail at minus 20 because the capacitor loses capacitance and the winding voltage falls.
Auto restart on every protection means a fault produces a hiccup rather than a latch. That is the right behaviour for a charger or a standby supply, and it complicates fault diagnosis in service, because a dead output can be a shorted secondary, an open feedback loop or a thermal event, all producing the same hiccup.
Where the part is used
Battery charger adapters, standby supplies for televisions and monitors, and auxiliary supplies for motor control are the applications the document names. In practice it appears in any board that needs 5 W to 13 W from the mains with a low component count and no electrolytic on the primary side for start up.
Our power management cross reference page lists the offline switchers we compare by power level and package, the component lead time solutions page covers what we do when the reel is not on the shelf, and the vendor consolidation page describes how we combine primary and secondary side parts on one shipment.
Three questions buyers ask about this string
Is the 13 W figure for any mains input? No. It is the 195 V to 265 V AC case. On the wide 85 V to 265 V AC range the DIP-8 figure is 8 W.
Does it need an optocoupler? The feedback path depends on the topology. A primary side regulated flyback can avoid it, and a secondary side regulated supply needs it for isolation.
Can the SO-8 version be used at 10 W? Not within the capability figures printed for that body. The DIP-8 string is the one rated for that power.