L6920DTR
Product Specifications
L6920DTR — Voltage Regulator by STMicroelectronics
The L6920DTR is an STMicroelectronics voltage regulator in TSSOP-8(3x4.4x0.65) for reliable power management in embedded and industrial applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| L6920DTR | Full Part Number | STMicroelectronics Voltage Regulator |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | L6920DTR |
| Package | TSSOP-8(3x4.4x0.65) |
| Type | Fixed/Adjustable Voltage Regulator |
| Qualification | Industrial (-40°C to +125°C) |
Product Overview
The L6920DTR is an STMicroelectronics voltage regulator in TSSOP-8(3x4.4x0.65) package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.
Key Features & Benefits
Stable Output with Built-in Protection
Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.
Wide Compatibility & Minimal External Components
Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.
Industrial Temperature Range
Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.
Target Applications
Drone & Embedded System Power Rails
Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.
Industrial & Automotive Electronics
Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.
General-Purpose Point-of-Load Regulation
Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.
Frequently Asked Questions
What is the output voltage of the L6920DTR?
Check the specific variant. The L6920DTR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.
What capacitors are needed for stability?
Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics L6920DTR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.
L6920DTR: a boost converter that starts at 1 V and runs down to 0.6 V
L6920DTR is a synchronous step up converter from STMicroelectronics in the TSSOP8 body, tape and reel. It runs from an input between 0.6 V and 5.5 V, guarantees start-up at 1 V, and produces a fixed 3.3 V or 5 V output, or an adjustable output from 2 V to 5.2 V with two resistors. Three external components are enough to complete the conversion, and the internal synchronous rectifier means there is no Schottky diode in the bill.
The input range is the point of the part. Two alkaline cells fall from 3.2 V to 1.8 V over their life, and a single lithium cell sits near 3.6 V and falls to 2.5 V. A converter that needs 2.5 V to start will not start on a nearly flat pair of cells, while this one starts at 1 V and keeps working down to 0.6 V, which is the difference between using the last of the cell and throwing it away.
Vendor figures for the fixed and adjustable versions
| Function | Synchronous step up converter with internal rectifier |
| Input voltage | 0.6 V to 5.5 V operating |
| Start-up voltage | 1 V |
| Output voltage | 3.3 V or 5 V fixed, adjustable from 2 V to 5.2 V |
| Internal switch | 120 milliohms active P channel device |
| External components | Three, an inductor and two capacitors |
| Control | Variable frequency, for efficiency across the load range |
| Shutdown current | Zero, through the shutdown pin |
| Other functions | Low battery detection, reverse battery protection |
| Package | TSSOP8 |
| Named applications | One to three cell battery devices, handheld instruments, phones, pagers, GPS, digital cameras |
| Package option on this code | Tape and reel, the D suffix is the tube part |
What a boost from two cells looks like
The vendor application figure runs a 2.5 V input to 3.3 V at 500 mA, which is 1.65 W out. The input current at that point is about 0.8 A once efficiency is counted, and the 120 milliohm switch drops 96 mV at that current, which is a small part of the 0.8 V gap the converter is closing. The inductor carries the full input current plus the ripple, so its saturation rating and its direct current resistance belong to the efficiency sum as much as the switch does.
Reverse battery protection matters more here than on a step down part, because the battery is the input and it is inserted by a user. The part survives a reversed cell without an external diode, which on a handheld product is the difference between a warranty claim and a working unit. The low battery detection output is the other useful function: it warns the load before the input falls below the start-up threshold and the converter stops.
Use and the pages that follow on
Typical uses are handheld instruments, GPS receivers, pagers and any product that runs from one to three cells. Related pages are power management cross reference, obsolete part cross reference hub for replacements as the family ages, and one stop BOM sourcing.
Questions buyers ask on this code
Whether a 3.3 V output is available from a 1 V input is the first, and the answer is that start-up is guaranteed at 1 V but the current available at that input is limited by the input current the coil can carry. The second is the difference between the D and the DTR suffix, which is the packaging rather than the part. The third is the output capacitor, which has to be low enough in equivalent series resistance for the variable frequency loop to stay stable, and an old electrolytic in that position is a common cause of a converter that starts and then drops out.