Contact Us

L78L33ABUTR

Brand: ST
L78L33ABUTR is a linear voltage regulator from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L78L33ABUTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

L78L33ABUTR — Voltage Regulator by STMicroelectronics

The L78L33ABUTR is an STMicroelectronics voltage regulator in SOT-89(SOT-89-3) for reliable power management in embedded and industrial applications.

Part Number Decoded — Field by Field

FieldValueMeaning
L78L33ABUTRFull Part NumberSTMicroelectronics Voltage Regulator

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberL78L33ABUTR
PackageSOT-89(SOT-89-3)
TypeFixed/Adjustable Voltage Regulator
QualificationIndustrial (-40°C to +125°C)

Product Overview

The L78L33ABUTR is an STMicroelectronics voltage regulator in SOT-89(SOT-89-3) package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.

Key Features & Benefits

Stable Output with Built-in Protection

Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.

Wide Compatibility & Minimal External Components

Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.

Industrial Temperature Range

Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.

Target Applications

Drone & Embedded System Power Rails

Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.

Industrial & Automotive Electronics

Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.

General-Purpose Point-of-Load Regulation

Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.

Frequently Asked Questions

What is the output voltage of the L78L33ABUTR?

Check the specific variant. The L78L33ABUTR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.

What capacitors are needed for stability?

Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics L78L33ABUTR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.

L78L33ABUTR: the 3.3 V L78L in the A grade, and why its input floor is 5.3 V

L78L33ABUTR is the 3.3 V member of the same L78L family, A grade, SOT-89, tape and reel. It delivers up to 100 mA, keeps the internal current limit and thermal shutdown of the family, and holds plus or minus 4 percent, which at 3.3 V is 3.168 to 3.432 V. The AB grade is the one specified over minus 40 to plus 125 degrees, which is the reason it is chosen on outdoor units and on boards that see the inside of an enclosure in summer.

The number that catches people is the input floor. The vendor prints the 3.3 V electrical table at an input of 5.3 to 20 V for a load of 1 to 40 mA, and that lower bound is not arbitrary. With 2 V of typical dropout, a 3.3 V output needs about 5.3 V at the input before the pass element has anything left to regulate with. An engineer who drops this part onto a 5 V rail and expects 3.3 V at 100 mA will see the output sag to about 3 V under load, and the fault will look like a board problem rather than a headroom problem.

What the vendor table gives for this voltage

Output voltage3.3 V, plus or minus 4 percent in the A grade, 3.168 to 3.432 V
Output current100 mA with adequate heat sinking
Test input voltage5.3 to 20 V at 1 to 40 mA
Maximum input30 V for the 3.3 to 9 V members
Dropout voltage2 V typical at 40 mA
Quiescent current6 mA maximum at 25 degrees in the C grade table, 5.5 mA at 125 degrees
Supply voltage rejection49 dB typical at 120 Hz
Output noise40 microvolts typical over 10 Hz to 100 kHz
Load regulation60 mV maximum, 1 to 100 mA, C grade table
Line regulation150 mV maximum, 6.3 to 20 V, C grade table
PackageSOT-89, tape and reel
Junction to ambient55 degrees per watt with 6 square centimetres of copper
Junction range, AB grademinus 40 to plus 125 degrees

Heat, dropout and the 5 V rail question

Feeding 5.3 V into a 3.3 V output at 80 mA dissipates 160 mW, which on the SOT-89 pad is a rise of less than 10 degrees. The same part on a 12 V input at 80 mA dissipates 700 mW and rises about 39 degrees, still inside the range but no longer comfortable at a 70 degree ambient. The part is a linear regulator, so every volt of headroom is paid for in heat and the input rail should be chosen with that in mind rather than inherited from the previous board.

The dropout curve also explains why the 3.3 V member is often used behind a 5 V switching supply rather than directly on a 5 V adapter. A 5 V rail that is really 5.0 V has 1.7 V of headroom, less than the 2 V typical dropout, so the regulator is already out of regulation before the load reaches its limit. A 5.5 V or 6 V intermediate rail restores the margin for a few milliwatts of extra loss.

Applications and the sourcing route

This part usually feeds a 3.3 V microcontroller rail, a low power radio module or the analogue supply of a sensor front end, where the switching noise of a buck converter would otherwise sit on the reference. In SUPERB builds it appears on the control card of an RF unit and on the interface board of a medical instrument, both cases where a linear post regulator is cheaper than filtering a switching stage. Related pages are power management cross reference, component lead time solutions when the A grade is on allocation, and one stop BOM sourcing.

Questions buyers ask on the 3.3 V member

The grade question is the same as on the 5 V part: C grade widens the window to plus or minus 8 percent, so 3.04 to 3.56 V, and that is outside what most 3.3 V logic will accept at the bottom. The second question is whether the 5 V rail can feed it, and the answer is only if that rail is at least 5.3 V under all load conditions. The third is substitution: a 3.3 V LDO such as an LD1117 or LDL1117 will do the same job with lower dropout and more current, at the cost of a different pinout and a minimum output capacitor that the L78L does not need.