Contact Us

L78L12ACUTR

Brand: ST
L78L12ACUTR is a linear voltage regulator from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L78L12ACUTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

L78L12ACUTR — Voltage Regulator by STMicroelectronics

The L78L12ACUTR is an STMicroelectronics voltage regulator in SOT-89(SOT-89-3) for reliable power management in embedded and industrial applications.

Part Number Decoded — Field by Field

FieldValueMeaning
L78L12ACUTRFull Part NumberSTMicroelectronics Voltage Regulator

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberL78L12ACUTR
PackageSOT-89(SOT-89-3)
TypeFixed/Adjustable Voltage Regulator
QualificationIndustrial (-40°C to +125°C)

Product Overview

The L78L12ACUTR is an STMicroelectronics voltage regulator in SOT-89(SOT-89-3) package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.

Key Features & Benefits

Stable Output with Built-in Protection

Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.

Wide Compatibility & Minimal External Components

Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.

Industrial Temperature Range

Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.

Target Applications

Drone & Embedded System Power Rails

Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.

Industrial & Automotive Electronics

Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.

General-Purpose Point-of-Load Regulation

Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.

Frequently Asked Questions

What is the output voltage of the L78L12ACUTR?

Check the specific variant. The L78L12ACUTR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.

What capacitors are needed for stability?

Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics L78L12ACUTR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.

L78L12ACUTR: the 12 V L78L in the C grade, for rails that start from 15 V or 18 V

L78L12ACUTR is the 12 V member of the L78L family, C grade, SOT-89, tape and reel. The C grade holds plus or minus 8 percent, which at 12 V is a window of 11.04 to 12.96 V, and it is specified from 0 to 125 degrees junction rather than the minus 40 degree floor of the AB parts. It delivers up to 100 mA with heat sinking, needs no external components apart from the usual capacitors, and protects itself with current limiting and thermal shutdown.

This voltage exists for a specific kind of rail: the gate drive of a power stage, the coil supply of a relay, the bias of an op amp chain that swings 20 V peak to peak, and the 12 V housekeeping rail of an industrial controller that runs from a 15 V or 18 V brick. In each case the load is small and the noise requirement is strict, which is exactly the shape a linear regulator handles better than a switcher.

Vendor figures for the 12 V member

Output voltage12 V, plus or minus 8 percent in the C grade, 11.04 to 12.96 V
Output current100 mA with adequate heat sinking
Maximum input35 V for the 12 to 15 V members
Dropout voltage2 V typical at 40 mA
Quiescent current6 mA maximum at 25 degrees, 5.5 mA at 125 degrees
Supply voltage rejection49 dB typical at 120 Hz for the C grade
Output noise40 microvolts typical, 10 Hz to 100 kHz
Packages in the familyTO-92, SO-8, SOT-89
Package on this codeSOT-89, tape and reel
Junction to ambient55 degrees per watt with 6 square centimetres of copper
Junction range, C grade0 to 125 degrees
Storage rangeminus 65 to plus 150 degrees

Working out the dissipation at 12 V out

The worst case for a 12 V linear regulator is the highest input. From an 18 V rail at 60 mA the part drops 6 V and dissipates 360 mW, which on a SOT-89 pad is a rise of about 20 degrees. From a 24 V rail at the same current it dissipates 720 mW and rises about 40 degrees, and that is where the 0 to 125 degree window of the C grade starts to matter less than the ambient inside the cabinet. Any board that runs this part from 24 V should be checked on the bench at the top ambient rather than at room temperature.

The C grade tolerance is a commercial decision as much as a technical one. Twelve volts plus or minus 8 percent is 11.04 V at the bottom, and a relay with a 10.8 V pull in threshold is still fine, while a 12 V sensor that needs 11.8 V is not. If the load has a tight window, the AB grade of the same voltage is the part to ask for, and the price difference is small compared with a field return.

Where it is used, and the related sourcing pages

Typical loads are relay coils on an industrial control board, the bias rail of a bipolar analogue chain, and the gate supply of a motor drive. The 12 V output also appears as the intermediate rail in a two stage linear chain, where a 24 V input feeds this part and a 5 V L78L follows it. Related pages for this family are power management cross reference, pin to pin cross reference for the 78L series alternatives, and BOM consolidation when the same board needs several voltages from one order.

Questions buyers ask on this code

Whether the C grade is acceptable depends entirely on the load window, and the honest answer is that it is fine for relays, lamps and op amp bias and not fine for a precision reference. The second question is the input ceiling: 35 V is the absolute maximum for this voltage, so a 36 V rail needs a different part rather than a different grade. The third is whether a switching regulator would be better, and above about 200 mA it usually is, because the linear part would be dissipating more heat than the load consumes.