Contact Us

VN7140ASTR

Brand: ST
VN7140ASTR is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine VN7140ASTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

VN7140ASTR — Integrated Motor Driver / Smart Power Switch by STMicroelectronics

The VN7140ASTR is an STMicroelectronics integrated motor driver / smart power switch in SO-8 for automotive and industrial actuator control applications.

Part Number Decoded — Field by Field

FieldValueMeaning
VN7140ASTRFull Part NumberSTMicroelectronics Motor Driver / Power Switch

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberVN7140ASTR
PackageSO-8
TypeIntegrated Motor Driver / Smart Power Switch
QualificationAutomotive AEC-Q100 / Industrial

Product Overview

The VN7140ASTR is an STMicroelectronics integrated motor driver / smart power switch in SO-8 package. Featuring ST's VIPower technology with monolithic integration of power MOSFETs, gate drivers, and protection/diagnostic circuitry, it simplifies motor control and high-side/low-side switching designs with reduced BOM count and enhanced reliability.

Key Features & Benefits

VIPower Monolithic Integration — Power + Control in One Package

ST's VIPower technology integrates N-channel power MOSFETs, gate drivers, charge pump, and comprehensive protection circuitry on a single die — eliminating external MOSFETs, bootstrap diodes, and sense resistors.

Comprehensive Protection & Diagnostics

Built-in overcurrent, overtemperature (thermal shutdown), undervoltage lockout, and load-dump protection with diagnostic feedback (current sense output, fault status flag) enables self-protecting designs suitable for safety-critical and autonomous systems.

Automotive-Grade Robustness

Designed to withstand harsh automotive and industrial environments including load dump, reverse battery, and extended temperature range for reliable operation in drone payload systems, robotics, and vehicle applications.

Target Applications

Drone Payload & Actuator Control

Drives brushed DC motors, solenoids, and resistive/inductive loads in drone gimbal systems, payload release mechanisms, landing gear actuators, and auxiliary power switching.

Automotive Body & Powertrain

Targets automotive applications including throttle control, EGR valves, HVAC actuators, mirror folding, headlamp leveling, and relay/lamp drivers — all requiring AEC-Q100 qualification.

Industrial Automation & Robotics

Powers motor control, valve actuation, and power distribution in industrial robots, conveyor systems, automated guided vehicles (AGVs), and factory automation equipment.

Frequently Asked Questions

What protection features does the VN7140ASTR include?

The VN7140ASTR features overcurrent protection, overtemperature shutdown, undervoltage lockout, and diagnostic feedback — ensuring robust, self-protecting operation in demanding environments.

Is external current sensing required?

No. The integrated current-sense output provides proportional load current feedback, eliminating the need for external shunt resistors and differential amplifiers.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics VN7140ASTR with full traceability and batch-level QA documentation. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.

VN7140ASTR: a single 140 milliohm high side channel

VN7140ASTR is a single channel automotive high side driver in the PowerSSO-16 body, on tape and reel. It holds 140 milliohm typical on resistance, a 12 A typical current limit and a 40 V transient ceiling, with an operating range of 4 V to 28 V and a maximum standby current of 0.5 microamp. The MultiSense pin reports load current, supply voltage and chip temperature on one multiplexed analog output.

This is the single channel member of the same family as the quad driver, and the electrical table is close enough that the choice between them is a channel count decision rather than a performance one. A module that drives one lamp uses one package; a module that drives four uses the quad and saves three packages, three decoupling networks and three diagnostic inputs.

Figures come from the VN7140AJ and VN7140AS data sheet read this round, which prints 40 V transient, 4 V to 28 V operating, 140 milliohm per channel, 12 A current limit and 0.5 microamp standby for both bodies.

The electrical window

FunctionSingle channel high side driver with MultiSense analog feedback
Maximum transient supply40 V
Operating range4 V to 28 V
On resistance140 milliohm typical per channel
Current limit12 A typical
Standby current0.5 microamp maximum
Logic levels3 V and 5 V CMOS compatible
DiagnosticsLoad current, supply voltage and chip temperature on one multiplexed pin
Fault detectionOverload, short to ground, short to supply, off state open load, thermal shutdown
Latch behaviourConfigurable latch off with a dedicated reset pin
Supply faults coveredLoss of ground, loss of supply, reverse battery with external components
PackagePowerSSO-16 for the AS string, SO-8 for the AJ string
QualificationAEC-Q100

Loss and the board under the package

At 140 milliohm, 2 A costs 0.56 W and 5 A costs 3.5 W. The first number is comfortable in a PowerSSO-16 on a modest copper area; the second needs a thermal check, because 3.5 W in a small package at 85 degrees ambient puts the junction close to the 150 degree limit even on a four layer board. The 12 A current limit is a fault rating, not a running current.

The single channel body has the whole package copper available for one die, which is why it can hold a little more continuous current than one channel of the quad at the same resistance. That is the argument for the single package when a module has one heavy load rather than four light ones.

Choosing between the AS and the AJ body

The two strings share an electrical table and differ in package: PowerSSO-16 for the AS, SO-8 for the AJ. The SO-8 body saves board area and the PowerSSO-16 body removes heat better. A customer who changes the body letter without checking the land pattern ends up with a part that does not fit, and the reel label is the only place the difference appears.

The MultiSense output needs a sense resistor and a settling window in the sampling routine. Because the pin also carries the temperature and supply readings, the selection logic and the timing are part of the measurement, and a controller that ignores them reads a plausible number that means something else.

Supply and support

Signal lamps, small solenoids, relay coils and sensor supply gating on a 12 V rail. The part is used where one load needs a real current reading and the module has no room for a quad.

We check the reel and the date code at goods in, and we compare the single and quad strings by channel count rather than by unit price. The power management cross reference page lays the family out by resistance and channel count, the incoming inspection plan page covers the goods in checks, and the pin to pin cross reference page describes the comparison before a body substitution.

Three questions buyers ask about this string

Is the AS body pin compatible with the AJ? No. PowerSSO-16 and SO-8 are different footprints with different thermal behaviour.

Can one channel drive a small motor? It switches one direction. Reversal needs a bridge.

What is the practical continuous current? It depends on the copper and the ambient. At 5 A the package already dissipates 3.5 W, so the thermal check decides, not the 12 A limit.