STM8S207C6T6
Product Specifications
STM8S207C6T6
ST — MCU & Embedded Processors
Product Overview
The STM8S207C6T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8S207C6T6: 32 Kbyte Flash STM8S MCU in LQFP48
STM8S207C6T6 is the 32 Kbyte Flash member of the STM8S 8-bit line in a LQFP48 body (7 by 7 mm), with 1024 bytes of true data EEPROM, 6 Kbyte of RAM, 38 general purpose I/O, 10 analog inputs and 16 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.
Order code and memory
| Order code | STM8S207C6T6 |
| Program Flash | 32 Kbytes |
| Data EEPROM | 1024 bytes, 300 kcycle endurance |
| RAM | 6 Kbytes |
| Package | LQFP48, 7 by 7 mm |
| Pin count | 48 |
| Maximum general purpose I/O | 38 |
| External interrupt pins | 35 |
| High sink outputs | 16 |
| ADC channels | 10 of 16 |
| Controller area network | not present |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 2.95 to 5.5 V |
| Maximum CPU clock | 24 MHz up to 105 C ambient |
| Flash access | zero wait states to 16 MHz |
| Core | Harvard, 3 stage pipeline, 80 instructions, 20 addressing modes |
| Timers | advanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer |
| Analog to digital converter | 10-bit, 10 channels, scan mode, analog watchdog, 14 clock cycles per conversion |
| ADC clock | 1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V |
| Serial interfaces | UART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz |
| Run current | 11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum |
| Low power | halt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off |
| Reset | power-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis |
| Identification | 96-bit unique ID, single wire interface module for debug and programming |
Points to check before this part goes on a BOM
The 32 Kbyte Flash array here is paired with 1024 bytes of true data EEPROM and 6 Kbytes of RAM. The EEPROM is separate memory with a 300 kcycle endurance, so calibration tables and counters keep their contents when the program array is erased, while the 10 kcycle Flash limit applies only to code updates. What usually catches a 32 Kbyte part is not the code space but the 6 Kbytes of RAM once a receive buffer, a stack for nested interrupts and a Modbus or LIN frame buffer are all present.
This is a 48-pin body, so the ADC has 10 of the 16 channels the die can offer and, more importantly, the VREF+ and VREF- pins are not bonded out. The reference is therefore VDDA, and a 3.3 V rail with 5 percent tolerance turns into 5 percent of the full scale, roughly 51 LSB at 10 bits, before the converter's own error is counted. On a 48-pin board the analog budget has to be decided from the rail, not from a separate reference.
There is no controller area network block in the STM8S207 line. The 208 counterpart on the same pin count carries the beCAN 2.0B controller, so a board that may later need CAN should be laid out with the 208 part from the start, since the two are pin compatible on the 48-pin body but not function compatible.
Where this order code fits
Panel controllers, motor drives with a serial link to a host, small industrial timers and battery powered instruments that need a real EEPROM and a 5 V tolerant I/O ring. The 24 MHz clock ceiling applies up to 105 C ambient, and above that the datasheet ceiling drops to 16 MHz. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the resource differences that decide the choice before any code is written.
Questions buyers ask
Can this part be clocked at 24 MHz? Yes, but only with the WAITSTATE option bit set, because zero wait states are guaranteed to 16 MHz. Above 105 C ambient the maximum drops to 16 MHz regardless of the option byte.
How much RAM is left for buffers? Out of 6 Kbytes, subtract the stack for the deepest interrupt nesting and any bootloader reservation. A 1 Kbyte serial buffer and a 512 byte frame buffer are realistic on this part; a 4 Kbyte image buffer is not.
Does the part have CAN? No. beCAN belongs to the STM8S208 line. For a CAN node on 48 pins the equivalent order code is STM8S208C6.
SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the How to Verify a Drop in Replacement page walks through the checks that keep a substitute from failing on the bench.