Contact Us

BQ25070DQCT

Brand: Texas Instruments
Texas Instruments BQ25070DQCT is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25070DQCT — Power Management & Signal Chain | Superb Automation

BQ25070DQCT

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25070DQCT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25070: a linear charger for LiFePO4 cells, with a 50 mA LDO on the same die

The BQ25070DQCT charges one LiFePO4 cell at up to 1 A from a USB port or an adapter, from a 30 V rated input with a 10.5 V overvoltage cut off. It is a linear charger, so there is no inductor and no switching node, and the external count is the input capacitor, the output capacitor and a few resistors.

The chemistry is the reason this part is separate from the Li-ion family. A LiFePO4 cell sits at 3.2 V nominal, floats at about 3.5 V and must not be taken to the 4.2 V that a Li-ion charger applies. The device regulates to 3.5 V float with a 3.7 V overcharge clamp, and the charge profile is the LiFePO4 one rather than a Li-ion profile with a lower setpoint. Putting a Li-ion charger on a LiFePO4 pack with the voltage resistor changed is a common shortcut, and it works only until the temperature compensation in the pack is asked to do something the charger does not know about.

The second block on the die is a 50 mA low dropout regulator at 4.9 V. That rail is there to run a small housekeeping load from the same input, so the product does not need a separate LDO for a display bias or a sensor supply. On a 2 mm by 3 mm board that is often the difference between two parts and one.

Key data for the BQ25070DQCT

FunctionSingle cell LiFePO4 linear charger with integrated LDO
Charge currentUp to 1 A, set by a single CTRL input
Current accuracy7 per cent charge current regulation
Charge voltage3.5 V float, 3.7 V overcharge clamp
Input rating30 V rating, 10.5 V input overvoltage protection
Default current300 mA with the ILIM resistor at its default value
LDO output4.9 V at 50 mA
MonitoringBattery NTC input, charge status output
ThermalThermal regulation loop, thermal shutdown, soft start to limit inrush
PackageSON, 10 pins, 2 mm by 3 mm, marking QUS

Body and ordering data

The ordering table prints two rows. bq25070DQCR is the large reel, 3000 pieces, and bq25070DQCT is the small reel, 250 pieces. Both carry the same default current of 300 mA, the same 3.5 V float, the same 3.7 V clamp, the same 10.5 V overvoltage threshold and the same 4.9 V LDO. The marking on both is QUS, which means the two reels cannot be told apart once the parts are out of the bag.

The single CTRL pin sets the charge current from one logic input rather than a resistor network. That is a deliberate simplification: the product either charges at the high rate from a wall adapter or at the low rate from a USB port, and one GPIO decides which. The cost is that the current is not continuously programmable.

Where the heat goes

A linear charger at 1 A from a 5 V adapter into a 3.3 V cell dissipates about 1.7 W. In a 2 mm by 3 mm SON with a thermal pad, that is a junction rise that the thermal regulation loop will limit by cutting the charge current. The part does not fail, it slows down, and a user who expects a one hour charge gets three.

The input voltage is the lever. Charging the same cell from a 5 V adapter rather than a 9 V one cuts the dissipation by more than half at the same current, because the drop across the pass device is smaller. Products that use a 12 V source with this part usually need the current reduced, not the package changed.

Where it fits in a build

Handhelds and instruments built around a LiFePO4 cell: portable test gear, backup units, small solar products and any device where the pack has to sit at a stable 3.2 V. The integrated LDO is useful where a sensor or a display needs a quiet 4.9 V rail. The power management cross reference page lists the LiFePO4 and Li-ion chargers we compare on chemistry and cell count.

A product with a Li-ion pack must not use this string, and a product that needs 2 A of charge current must not either. The part is a 1 A linear charger, and the current figure is set by the thermal path as much as by the die.

The sourcing side of this part is covered on the how to reduce component cost. For a product where the LDO and the charger share one input, that page covers the part count and the input rating changes that decide the cost of the front end.

Questions we get on this code

Can it charge a Li-ion cell at 3.5 V? It will charge it, and the cell will never be full. The float voltage is the LiFePO4 one.

Is the 4.9 V LDO available while charging? Yes, it runs from the input, so it is present whenever the adapter is connected and absent on battery alone.

What is the difference between the DQCR and the DQCT rows? Reel size only, 3000 against 250. The body and the electrical behaviour are identical.

Does the NTC input have to be used? The pin expects a thermistor. A fixed resistor in its place removes the temperature based charge suspend, which on a LiFePO4 pack in an outdoor enclosure is the protection that matters most.