Contact Us

BQ24171RGYR

Brand: Texas Instruments
Texas Instruments BQ24171RGYR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ24171RGYR — Power Management & Signal Chain | Superb Automation

BQ24171RGYR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ24171RGYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ24171: a stand alone 4 A charger for one to three cells, with JEITA built in

The BQ24171RGYR charges one, two or three Li-ion cells in series from an adapter between 4.5 V and 17 V, with a 30 V input rating and an adjustable overvoltage threshold. The switching stage runs at a fixed 1.6 MHz and the two N-channel FETs are inside the package, so the converter needs an inductor, a few capacitors and a sense resistor rather than a controller plus external switches.

The part is stand alone: there is no I2C port and no host needed to charge. Current, voltage, input limit and the temperature profile are all set with resistors. That is deliberate. A battery bay charger, a portable printer or a medical diagnostic unit often has no processor to spare for charge management, and a part that needs a driver and a watchdog is a liability in those products.

The JEITA behaviour is the feature that separates it from a plain CC/CV charger. Below the cold threshold the charge current is cut. Above the warm threshold the regulation voltage is cut. Between the two it charges normally. On a pack that sits in a vehicle or a outdoor enclosure, that profile is the difference between a pack that lasts three years and one that swells in the first summer.

Key data for the BQ24171RGYR

FunctionStand alone synchronous switch mode charger, one to three cells
Input range4.5 V to 17 V operating, 30 V rating with adjustable OVP
Switching frequency1.6 MHz nominal, 1.36 MHz to 1.84 MHz across the tolerance
Charge currentUp to 4 A with the integrated 20 V N-channel FETs
EfficiencyUp to 94 per cent
Voltage accuracyPlus or minus 0.5 per cent charge voltage regulation
Cell countAdjustable charge voltage up to three series cells
ThermalRegulation loop throttles current to hold the junction near 120 C, shutdown above it
Power pathAutomatic selector between adapter and battery, dynamic power management
PackageVQFN, 24 pins, 5.5 mm by 3.5 mm
TemperatureMinus 40 to 85 C operating

Body and ordering data

BQ24171RGYR is the active row, VQFN RGY with 24 pins, 3000 pieces on a large tape and reel, NIPDAU finish, moisture level 2 with a one year floor life at 260 C, minus 40 to 85 C, marking BQ24171. The G4 row carries the same body and the same quantity.

The 85 C ceiling is the number to read twice. This is not an automotive or a hot enclosure part. A medical diagnostic unit that is autoclaved, or a charger inside a sealed box next to a 40 W load, will run the junction past 85 C ambient long before the charge current is the limiting factor. The thermal regulation loop will protect the die by cutting current, and the symptom the user sees is a pack that never finishes charging.

Reading the input side correctly

The 30 V rating is a survival figure and the 17 V figure is the operating window. Between them sits the adjustable overvoltage protection, which is set by a resistor divider and should be placed just above the highest legitimate adapter voltage with margin for cable ringing. Set too close, and a 19 V notebook adapter with a long cable trips protection on insertion. Set too far, and the protection never acts before the 30 V absolute maximum is reached.

The dynamic power management loop works the way the rest of the family does: when the adapter sags, charge current is reduced to hold the input above the threshold, and the system rail stays up. On a stand alone part there is no host to notice, so the resistor values are the only tuning available.

Where it fits in a build

Tablet and netbook packs, portable data terminals, portable printers, medical diagnostic equipment and battery bay chargers. Any of those with a two or three cell pack and no host processor is the natural fit. The power management cross reference page lists the cell counts and input windows we compare when this string is not available.

For a single cell pack with a host, a part with an I2C port gives more control and a smaller external count. The stand alone route wins when the charger has to work with no software at all, including during production test, before any code is loaded.

The sourcing side of this part is covered on the how to reduce component cost. When one board has to serve a two cell and a three cell pack, that page covers the resistor and sense changes that keep a single part across both builds.

Questions we get on this code

Can it charge three cells from a 12 V adapter? Yes, within the current limit. The charge current has to fall as the pack voltage rises, because the input power is fixed, and the 4 A figure is only reachable at the lower cell counts.

Why does the part get warm at 4 A? The FETs are inside, and 4 A through the high side switch dissipates real power. The thermal regulation loop is what keeps that from becoming a failure, and the board copper under the thermal pad sets the ceiling.

Does it need a thermistor? The TS pin expects one, and without it the temperature profile cannot work. A fixed resistor in its place disables the JEITA behaviour, which is legal but removes the protection the pack was specified for.

Is the 1.6 MHz figure fixed? It is fixed in the sense that there is no external clock, but the tolerance runs from 1.36 MHz to 1.84 MHz. An inductor chosen at exactly 1.6 MHz with no margin will be at the edge of its ripple current at the low end of that band.