BQ24157YFFR
Product Specifications
BQ24157YFFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ24157YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ24157: a 1.55 A switch mode charger that fits on a 2.1 mm square die
The BQ24157YFFR is a single cell Li-ion and Li-polymer charger with the power FETs, the current sense and the control loop inside one 20 ball chip scale package. The die is 2.1 mm by 2.0 mm. It is built for a phone or a handheld where the charger sits next to the connector and the battery flex, and where the board area left for charging is a few square millimetres.
What separates it from a linear charger of the same current class is the switching stage. A linear part burns the difference between the adapter voltage and the cell voltage as heat, so a 5 V adapter charging a 3.7 V cell at 1 A turns about 1.3 W into the package. The BQ24157 regulates with a synchronous converter instead, and the same 1.55 A arrives with far less heat, which is why the document lists it as the faster route for a pack that has to take charge while the phone is running.
The part also boots the system with no battery fitted. In that state it holds the system rail at a regulated level from the adapter alone and lets the processor start, which is what a factory test fixture needs before the pack is plugged in.
Key data for the BQ24157YFFR
| Function | Single cell switch mode charger with power path and USB OTG boost |
| Input rating | 20 V absolute maximum, 6.5 V maximum operating input |
| Charge current | Up to 1.55 A with a 55 milliohm sense resistor |
| Voltage accuracy | Plus or minus 0.5 per cent at 25 C, plus or minus 1 per cent from 0 to 125 C |
| Current accuracy | Plus or minus 5 per cent at the 100 mA and 500 mA USB settings |
| Regulation range | 3.5 V to 4.44 V charge voltage, set over I2C |
| Input voltage DPM | Programmable 4.2 V to 4.76 V, accuracy minus 3 to plus 1 per cent |
| Input overvoltage | 6.5 V threshold, with bad adapter detection and rejection |
| Boost mode | 3.2 V to 4.5 V from the battery for USB on the go |
| Interface | I2C up to 3.4 Mbps, with a safety limit register |
| Package | DSBGA, 20 balls, 2.1 mm by 2.0 mm |
| Temperature | Minus 40 to 125 C operating |
Body and ordering data
The orderable row is BQ24157YFFR, active and in production, in the YFF body with 20 balls, 3000 pieces on a large tape and reel. The finish is SNAGCU, moisture level 1 at 260 C with no floor life limit, and the part marking is BQ24157A. The .A and .B rows of the same string carry the same carrier and quantity, so a quote that names the string alone does not tell you which revision of the die is in the reel. Ask for the row, not the family name.
Moisture level 1 matters on this body more than on a leaded package. A chip scale part with 20 balls on a 2 mm die has almost no compliance, and a reel that has taken on moisture will show it as cracked balls after the second reflow rather than as a visible defect at incoming inspection.
What the DPM loop and the bad adapter check actually do
The input voltage based dynamic power management loop watches the voltage at the input and folds the charge current back before that voltage collapses. On a long USB cable with a weak wall adapter, the adapter output sags as current rises. Without the loop the charger keeps asking for 1.55 A, the adapter drops below its own regulation point, and the system rail falls with it. With the loop, the charger gives up charge current to hold the input above the programmed threshold, so the phone keeps running and the pack charges slower instead of the whole rail browning out.
The bad adapter detection works in the same window. A source that cannot hold its voltage under a short test load is rejected and the charger stays off, which protects the input from a supply that is not what its label claims. Both behaviours depend on the threshold being set for the actual adapter, and the register default is not always the value a given product wants.
Where it fits in a build
This is a phone and handheld part first, and a medical handheld second. Any product with a single cell, a USB port and a processor that has to start before the pack is fitted can use it, provided the charge current in the application stays under 1.55 A. For a two cell or three cell pack, the power management cross reference page lists the parts we compare on cell count and input rating before we offer a substitute.
Builds that run from a 12 V adapter rather than USB need a different input rating entirely. The 20 V absolute maximum here is a survival figure, not an operating window, and a 12 V rail that rings on hot plug will exceed 20 V at the pin if the front end has no clamp.
The sourcing side of this part is covered on the component lead time solutions. For a build that is already committed to this string and facing a delivery gap, that page sets out what we check on stock, date code and packaging before a substitute is offered.
Questions we get on this code
Is the 1.55 A available from a 500 mA USB port? No. The input current limit has to be set to what the port can deliver, and the charge current then follows from the input power available. Setting the limit to 500 mA and the charge current to 1.55 A gives a charger that folds back continuously, which is legal but slow.
What is the difference between the YFFR and the YFFT rows? The R suffix is the large reel and the T suffix is the small reel. The die and the body are the same, so a line that runs a few hundred pieces a week can take the small reel and save the setup time of a full one.
Can it run with the battery removed? Yes, that is one of the stated features. The system rail is regulated from the adapter while the pack is absent, and the loop enters high impedance mode if the input cannot support the load.
Do you hold this string in stock? We quote from confirmed vendor stock and from our own buffer rather than from a catalogue claim, so the answer changes week to week. Send the quantity and the target date and the reply names the actual date code on offer.