DRV8832DRCR
Product Specifications
DRV8832DRCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8832DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8832DRCR: the same 1 A bridge in a 3 mm leadless body
The DRV8832DRCR is the 10-pin VSON body of the DRV8832, the low voltage single H-bridge driver with a voltage regulation loop. Electrically it is the same circuit as the HVSSOP version: 2.75 V to 6.8 V supply, 1 A DC or RMS and 1.3 A peak, 450 mOhm high side plus low side, a programmable voltage loop, an adjustable current limit, a fault output, and 300 nanoamps of sleep current. What differs is the body and therefore the thermal path and the assembly process.
The VSON outline is 3.00 mm by 3.00 mm with 9 mm squared of area, and the thermal pad is the only path out of the die. On a board with a solid copper plane under the part and a grid of vias in the pad, the part removes its heat well; on a two layer board with a thin trace under the pad it does not. That is the whole engineering difference between this body and the HVSSOP at 3.00 mm by 4.90 mm, which has longer leads and 14.7 mm squared of area.
Functionally, the regulation loop is why an engineer picks this circuit at all. The motor sees a regulated average voltage rather than the raw pack voltage, so a toy, a toothbrush or a portable printer runs at the same speed on a fresh cell and on one at 3.1 V. A built in reference output feeds the setting divider, an external resistor sets the current limit, and a fault pin reports an overcurrent or thermal event to the controller.
Sleep current of 300 nanoamps is the other number that matters in a battery product. A driver that leaks a milliamp will flatten a coin cell in weeks even when the product is off, and this one does not. The operating temperature range is minus 40 C to plus 85 C, the same as the other body.
Key data for the DRV8832DRCR
| Operating supply | 2.75 V to 6.8 V, absolute maximum 7 V |
| Output | One H-bridge, 450 mOhm high side plus low side |
| Current | 1 A DC or RMS, 1.3 A peak, limited by the thermal path of the 3 mm body |
| Regulation | PWM voltage regulation against a programmable reference, built in reference output |
| Current limit | Adjustable, acts during start up and stall |
| Fault reporting | Fault output pin to the host controller |
| Sleep current | 300 nanoamps typical |
| Protection | Overcurrent, short circuit, undervoltage lockout, thermal shutdown |
| Temperature | Minus 40 C to plus 85 C operating |
Body, packing and marking data
| Body in this code | 10-pin VSON, the DRC outline, 3.00 mm by 3.00 mm, 9 mm squared with a thermal pad |
| Other body | 10-pin HVSSOP, the DGQ outline, 3.00 mm by 4.90 mm, 14.7 mm squared with a PowerPAD |
| Carrier | Tape and reel; the count per reel is read from the vendor addendum row for this order code |
Reading the code before you buy it
DRV8832 is the circuit, DRC is the 3 mm VSON and the trailing R is the reel. The DGQ version of the same circuit is the HVSSOP, and the two are not interchangeable on a board. A production line that has been running the DGQ body and switches to the DRC without a board change will find that the pads do not line up, which is the kind of mistake that reaches the pick and place machine before anyone notices.
Because the two bodies are electrically identical, a datasheet figure read on one applies to the other. That is useful during a shortage: the electrical check on a substitute is short and the mechanical check is the long one. Our how to verify a drop in replacement page describes the order we run those checks in, body first, then the electrical confirmation.
The VSON has no visible leads, so the solder joint can only be inspected from the side or by X-ray. A build that has to pass a visual inspection standard should either use the HVSSOP or accept an X-ray step on the first article, and that cost is usually larger than the board area the smaller body saves.
Where the DRV8832DRCR fits
Handheld and wearable products where the board is small and the motor is a vibration or a pump motor of a few hundred milliamps: smart watches with a haptic motor of the ERM type, portable infusion pumps, electric shavers, and the lens cover or zoom mechanism in a compact camera. The 3 mm body is what makes it fit beside the battery connector.
Portable printers and label makers use it for the paper feed in the same small form factor, and the voltage loop keeps the print speed constant as the battery falls. Toys and small appliances use it where the cost of board area dominates and the thermal load is light.
Where the body becomes the limit is a motor that draws close to 1 A continuously. The 9 mm squared pad removes less heat than the HVSSOP, so the same current that is comfortable in the larger body reaches the thermal shutdown in this one. A continuous 1 A load is the case to check with a thermal measurement rather than a calculation. Our PCBA quote checklist page lists the questions we ask before quoting a build with a thermally tight part on it.
Questions we get on this code
Is the DRC version cheaper? Often yes, because the leadless body uses less material and a smaller reel pitch, and the difference is a fraction of a cent at volume. At low volume the difference is inside the noise and the assembly cost of the X-ray step is larger than the part saving.
Can the pad be connected to the bottom layer only? The pad is the only thermal path, so it has to reach a copper area. A single via to a bottom layer helps a little and a grid of vias into an inner plane helps a lot. A pad connected to nothing is the failure mode that shows up as a driver that works on the bench and shuts down in the enclosure.
Does the part need an external flyback diode? No, the bridge FETs carry the recirculation. What the board needs is a capacitor at the supply pin close to the part, because the current loop switches at the PWM frequency and a long supply lead turns that into a voltage spike at the pin.
Is the voltage loop stable with any motor? The loop is compensated for the range of inductances in small motors and the vendor gives an external component set for it. A motor with very low inductance changes the loop behaviour, and that is the case where the current waveform should be looked at on a scope before the board is released.