STM32L052C8T6
Product Specifications
STM32L052C8T6
ST — MCU & Embedded Processors
Product Overview
The STM32L052C8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32L052C8T6: 64 Kbyte, LQFP48 body
STM32L052C8T6 is a member of the STM32L052x6/x8 low power line described by DS10182 Rev 10. The order code fixes 64 Kbytes of Flash, 8 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V supply.
Order code and memory
| Order code | STM32L052C8T6 |
| Program Flash | 64 Kbytes |
| SRAM | 8 Kbytes |
| Data EEPROM | 2 Kbytes with ECC |
| Package | LQFP48, 7 x 7 mm, 48 pins |
| Maximum general purpose I/O | 37 |
| Analog input channels | 10 channels on the 12 bit converter |
| Digital to analog converter | 1 channel of 12 bits |
| Segment LCD driver | not present on this part |
| Supply voltage | 1.65 to 3.6 V |
| Maximum CPU clock | 32 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient |
| Datasheet | DS10182 Rev 10 |
Peripheral and electrical parameters
| Core | ARM Cortex-M0+ at up to 32 MHz, 0.95 DMIPS per MHz, memory protection unit |
| Clock sources | 1 to 25 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC and a PLL for the core clock |
| Low power modes | 88 microamps per MHz in Run mode, 0.8 microamps in Stop with the RTC and 8 Kbytes of RAM retained, and 5 microseconds wakeup from flash |
| Timers | nine timers: one 16 bit with four channels, two 16 bit with two channels, one 16 bit low power timer, one 16 bit basic timer for the DAC, the RTC, SysTick and the two watchdogs |
| Serial interfaces | up to four SPI blocks of which one is I2S, two I2C blocks with SMBus and PMBus, two USARTs with ISO 7816 and IrDA, one UART, one LPUART and one USB 2.0 port that runs without a crystal |
| Analog | one 12 bit ADC at 1.14 Msps, one 12 bit DAC channel and two ultra low power comparators |
| Memory interface | not present on this body |
| Flash and EEPROM endurance | flash and EEPROM cycling are listed separately, with 30 years of retention at 85 C after 10 kcycles and 10 years at 105 C |
| Thermal resistance junction to ambient | 55 C/W on LQFP48 |
| Input tolerance | 45 of the 51 I/O on the 64 pin body are 5 V tolerant |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | the VBAT domain keeps the RTC and the backup registers alive with the main rail off |
| Status | full production per the datasheet cover |
Points to check before this part goes on a BOM
The order code is C for 48 pins, 8 for 64 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. The 052 prefix carries the crystal-less USB port and a 12 bit DAC channel, and it has no segment driver, which belongs to the 053 code in a separate document.
The USB port runs without a crystal because the internal 48 MHz RC is trimmed against the USB frame, which removes two capacitors and a crystal from a small board and is the reason this code is picked over the 051 for an interface product.
8 Kbytes of SRAM and 2 Kbytes of EEPROM is a small budget: a USB stack with endpoints, a command parser and a buffer fit, and a file system does not. A dongle that exposes a few registers over USB and stores one calibration block is inside the budget, and a data logger is not.
0.8 microamps in Stop with the RTC and 8 Kbytes of RAM retained is 7 mAh over a year, and 5 microseconds wakeup from flash is what makes a duty cycled sensor practical. The part can be asleep for a second, wake, convert, transmit and be back in Stop before the next tick.
The LQFP48 is rated 55 C/W junction to ambient, so 364 mW at an 85 C ambient against a 105 C junction. At 88 microamps per MHz the core draws 2.82 mA at the full 32 MHz, which is about 5 mW, so the I/O and the USB transceiver own the budget.
Ten analog channels on the LQFP48 against sixteen on the 64 pin body is the usual reason to move up: the converter is the same 1.14 Msps 12 bit block and only the bonded inputs change. A board with a battery monitor, two thermistors and a strain gauge is already at four.
The DAC channel is a single 12 bit output with an output buffer, enough for a setpoint or a bias and not for audio. It shares pins with the comparator inputs, so a board that wants both an analog output and a comparator threshold has to check the pin table.
The 64 pin code R8T6 carries the same 64 Kbytes and 8 Kbytes of SRAM with 51 I/O and 16 channels, so the substitution question between the two bodies is pins and not memory. The 053C8T6 adds the segment driver in the same 48 pin footprint.
Where this order code fits
It is the 64 Kbyte, 48 pin member with a crystal-less USB port, used on dongles, sensor interfaces and small instruments that enumerate over USB from a coin cell budget. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
Does the USB port need a crystal? No. The internal 48 MHz RC is trimmed against the USB frame, so the part enumerates without an external crystal. That is the main difference from the 051 code, which has no USB port at all.
How much RAM is left for a USB stack? 8 Kbytes in total. A device stack with a few endpoints, a command parser and a 512 byte buffer fits; a mass storage implementation with a file system does not.
Can it drive a segment display? No. The display driver belongs to the STM32L053 code in the same 48 pin body. STM32L053C8T6 is the equivalent with 4x18 segments.
What is the thermal budget on this package? 55 C/W junction to ambient, which is 364 mW at an 85 C ambient and a 105 C junction. The USB transceiver and the I/O current are what use it, not the core.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.