Contact Us

DS90LV028ATMX-NOPB

Brand: Texas Instruments
Texas Instruments DS90LV028ATMX-NOPB is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DS90LV028ATMX-NOPB — Power Management & Signal Chain | Superb Automation

DS90LV028ATMX-NOPB

Texas Instruments — Power Management & Signal Chain

Product Overview

The DS90LV028ATMX-NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DS90LV028ATMX-NOPB: a dual LVDS receiver in an eight pin body

The DS90LV028ATMX-NOPB is a dual low voltage differential signalling receiver, published ACTIVE, that takes two LVDS pairs in and gives two 3 V CMOS outputs. It runs above 400 megabits per second, or 200 MHz, on a 3.3 V supply and dissipates 18 mW static, which is a fraction of what an emitter coupled logic receiver costs for the same function. The differential input threshold is 100 mV in each direction, so a 350 mV differential signal is comfortably inside the window.

The part is used where a fast serial link has to cross a backplane or a cable and the receiver sits on a board that cannot afford the power of a PECL front end. Its flow through pin out puts the inputs on one side and the outputs on the other, which keeps the differential pairs short and straight, and that is the reason it has survived in printer and automation equipment for two decades.

The DS90LV028ATMX-NOPB rows as the addendum publishes them

Part classDual LVDS receiver, CMOS output
Vendor statusACTIVE, production data
Data sheetSNLS013F, June 1998, revised June 2016
Supply3.3 V, interoperable with 5 V LVDS networks
Switching rateAbove 400 megabits per second, 200 MHz
Differential input high threshold100 mV at common modes of 0, 1.2 and 3 V
Differential input low thresholdMinus 100 mV at the same common modes
Propagation delay1.0 ns minimum, 1.6 ns typical, 2.5 ns maximum
Differential pulse skew50 ps typical, 400 ps maximum
Channel to channel skew0.1 ns typical
Output high2.7 V minimum at 0.4 mA
Output low0.3 V typical, 0.5 V maximum at 2 mA
Supply current5.4 mA typical, 9 mA maximum, inputs open
Static power18 mW at 3.3 V
Input current1 µA typical, 10 µA maximum at 2.8 V
Short circuit current15 mA minimum, 50 mA typical, 100 mA maximum
FailsafeOutput high on open, shorted or terminated input
StandardANSI/TIA/EIA-644
Body, SOIC8 pins, 4.90 by 3.91 millimetres
Body, WSON8 pins, 4.00 by 4.00 millimetres
Tube rowDS90LV028ATM/NOPB, 95 pieces, tube, level 1
Reel rowDS90LV028ATMX/NOPB, 2500 pieces, level 1
Small reel rowDS90LV028ATMX/NOPB WSON, 1000 pieces, level 3
Marking90LV028ATM on the SOIC body

The SOIC rows are level 1, so the floor life is unlimited, and the WSON row is level 3 with a 168 hour window. That is the reverse of what most buyers expect, because the smaller body is usually the more robust pack. In practice the WSON is the row to avoid on a low volume line that opens and closes reels, and the SOIC is the row to specify when the board has space for it.

What 400 megabits per second means at the board level

A 400 megabit link has a 2.5 ns bit period, and the receiver's own propagation delay is up to 2.5 ns, so the delay is a full bit. That is not a problem for a source synchronous link where the clock travels with the data, because the delay applies to both. It is a problem for a link where the receiver's delay has to fit inside a fixed window, and that is why the pulse skew of 50 ps matters more than the absolute delay: it is the skew that closes the eye.

The 100 mV threshold means the differential signal at the receiver pins can have lost most of its amplitude and still be read. A driver that launches 350 mV into a cable with 20 dB of loss at 200 MHz delivers 35 mV, which is below the threshold, so the practical length limit is set by the cable loss rather than by the receiver. For a backplane of half a metre the margin is large; for a ten metre cable it is not.

The failsafe question

Open, shorted and terminated inputs all produce a high output, which means a disconnected cable reads as an idle line rather than as noise. That matters for a protocol that treats a high as marking, because the receiver then produces framing errors instead of random data, and the controller can detect the disconnect. A receiver without failsafe produces a random pattern on a disconnected pair, and the controller sees valid looking garbage.

The failsafe is built into the input stage rather than switched in, so there is nothing to configure. The only condition it does not cover is a pair that is driven to a valid differential zero, which is a live driver fault rather than a disconnected cable.

Termination and the eight pin body

LVDS needs a 100 Ω termination at the receiver, and the DS90LV028A does not include it. The resistor goes across the pair as close to the pins as possible, and on a two layer board that placement is the whole difference between a clean eye and a ringing one. The part is specified with a 100 Ω termination, so leaving it out changes the threshold behaviour as well as the waveform.

The eight pin body has room for two pairs and two outputs and nothing else, so the termination and any common mode choke have to live outside. On a dense board that is an advantage, because the parts can be placed where the pairs arrive rather than where the receiver sits.

Buying DS90LV028ATMX-NOPB

Three live rows: a 95 piece tube, a 2500 piece SOIC reel and a 1000 piece WSON small reel. The tube is the right quantity for a prototype or a service kit, and it is level 1 so it can sit on a shelf indefinitely. The reel is a normal production quantity for a printer or a motor drive that uses one receiver per axis.

The marking 90LV028ATM does not include the DS prefix, which is a detail that trips a first article inspection comparing the package with the purchase order string. The reel label carries the full string and is the document to check.

Questions that arrive with this part number

Whether it can replace a PECL receiver is the first, and the answer is usually yes with a change in termination and a check on the common mode range, because PECL and LVDS sit at different offsets. The second is whether the part can drive a 5 V CMOS load. The output is 3 V CMOS and will drive a 5 V input only if that input has TTL thresholds, which most do.

The third is the difference between this part and a serialiser pair. A serialiser takes parallel data and embeds a clock, while this receiver expects the clock to arrive on a separate pair. For a link that already carries a clock, the receiver is the simpler and cheaper choice.

Pre-emphasis is the usual companion to a long link. A driver with pre-emphasis boosts the first part of each edge, which compensates for the cable high frequency loss, and the receiver with a 100 mV threshold then sees a usable eye at the far end. Without it, the practical length at 400 megabits is a few metres of good cable, and the eye closes quickly beyond that. A receiver with a 100 mV threshold is the reason a passive equaliser at the driver end is usually enough for ten metres of twisted pair.

A last point on the pack: the 95 piece tube has no floor life limit while the WSON small reel does, so a service kit can hold tubes indefinitely and a production line should buy the SOIC reel and keep the WSON for boards that cannot spare the area.

For a programme that is choosing a receiver for a backplane, the pin to pin page lists the interface families, and the incoming inspection plan covers the marking check on the tube and reel rows.