INA111BP
Product Specifications
INA111BP
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA111BP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA111BP: the tighter offset bin of the FET input family in a plastic DIP
The INA111BP is the B grade of the INA111 family in the eight pin plastic DIP, and the grade is the only thing that separates it from the AP in the same body. The offset is laser trimmed to a tighter window, which matters on a channel that is not trimmed at test, and the drift specification is the same 5 µV per degree. Everything else is shared: current feedback topology, 2 MHz at a gain of 10, 4 microseconds settling to 0.01 per cent at a gain of 100, 20 pA maximum bias current, and 106 dB of common mode rejection at a gain of 100.
The plastic DIP is a through hole part and is bought in tubes of 50. That is a deliberate choice on a board that has to be reworked by hand or that sits in a socket, and it is a problem on a line that only runs reels. The same die is available in the 16 pin SOIC under the BU suffix, with the same tighter offset bin.
The INA111BP rows as the addendum publishes them
| Part class | FET input instrumentation amplifier, B grade offset bin |
| Vendor status | ACTIVE, production data |
| Data sheet | SBOS015, March 1998 |
| Gain equation | G = 1 + 50 kΩ divided by RG |
| Gain range | 1 to over 1000 V/V |
| Input bias current | 20 pA maximum |
| Offset drift | 5 µV per degree maximum |
| Offset at unity gain | The tighter of the two bins in the family table, scaled by gain |
| Common mode rejection at G = 100 | 106 dB minimum |
| Input noise at 1 kHz | 13 nV per root Hz |
| Bandwidth at G = 10 | 2 MHz |
| Settling to 0.01 per cent | 4 µs at G = 100 |
| Gain error at G = 1 | 0.01 per cent typical, 0.5 per cent maximum |
| Nonlinearity at G = 1 | 0.0005 per cent typical, 0.005 per cent maximum |
| Supply range | 6 V to 18 V |
| Quiescent current | 3.3 mA typical, 4.5 mA maximum |
| Output swing | 11 V minimum at 5 mA |
| Capacitive load stability | 1000 pF |
| Body | PDIP, P outline, 8 pins |
| Carrier | 50 pieces in a tube |
| Lead finish | Nickel palladium gold on the current row |
| Moisture level | Not applicable to this package type on the current row |
| Temperature range | Minus 40 to plus 85 degrees |
| Part marking | INA111BP |
The addendum shows two rows for this string, the plain one and the A revision, and the lead finish and moisture columns differ between them. The plain row reads call the vendor for the finish while the revision row carries nickel palladium gold and level 3, which is the pattern the vendor uses when a part has moved between assembly sites. A receiving inspection that reads only the part number and not the revision suffix will occasionally find a finish it did not expect.
Two bins, one data sheet, and a calibration step
The A and B grades sit in adjacent columns of the same table, which makes it easy to read the wrong one. The practical difference is whether the channel needs a trim. A 1 per cent accuracy target on a 10 V full scale allows 100 mV of error, and both grades meet that easily at unity gain. The same target on a 10 mV full scale allows 100 µV, which is inside the B grade and outside the A grade once drift over 40 degrees is added. A customer who signs a 1 per cent specification on a 10 mV channel with the A grade has signed for a trim step whether they know it or not.
The trim itself is not free. A potentiometer is a part, a labour step, and a drift source, and on a board that is potted it is also a reliability question. Paying the grade premium is usually cheaper than adding a trim, which is why the B grade exists at all.
Socketed through hole parts and the contact resistance question
A plastic DIP in a socket is common in instruments that are serviced, and the socket adds two contacts in series with each input. A 100 mΩ contact is nothing against a 5 x 10^12 Ω input impedance, but the contact is also a thermocouple: two dissimilar metals at the socket pin generate a few microvolts per degree, and that voltage appears in series with the signal. On a channel measuring 10 mV, a 5 µV thermal EMF is 0.05 per cent of full scale and it drifts with the room.
The usual answer is to solder the part and socket the sensor connector instead, so the thermal junction sits at a known point that can be isothermal with a copper block. Where a socket is unavoidable, a gold plated contact against the nickel palladium gold lead finish is the lowest EMF pair available on this part.
Input protection and the price of a series resistor
The part tolerates input voltages from 0.7 V below the negative rail to 15 V above the positive rail, which is wide enough for most fault conditions and not wide enough for a lightning induced transient on a long cable. The standard guard is a 1 kΩ series resistor and a pair of clamp diodes, and the resistor costs 1 kΩ of source imbalance. Against a 20 pA bias current that is 20 nV, which is nothing; against a 10 pA offset current it is 10 nV. The real cost is the thermal noise of the resistor, 4 nV per root Hz for 1 kΩ, which is small compared with the 13 nV per root Hz of the amplifier.
The diode leakage is the part that gets forgotten. A small signal diode leaks nanoamps at room temperature and microamps when warm, and that leakage flows through the source impedance. A channel that needs the full 20 pA bias current specification cannot have a leaky clamp across the input; a low leakage diode or a series resistor large enough to swamp the leakage is the answer, and the two choices trade noise against leakage.
Buying INA111BP
The tube of 50 is the only carrier, the part is active, and the die is shared with three other strings in the family. That makes stock straightforward and price the only variable, which is unusual for a part of this age. A broker offering this string at a large discount is offering either a re marked part or a tube that has been through a reflow, and on a part with a laser trimmed offset both are easy to detect at incoming test.
The grade is the thing to verify on receipt. The marking on the body reads INA111BP for the B grade and INA111AP for the A grade, so a tube that is labelled B and marked A is a substitution that a functional test will not catch at unity gain but a drift test over temperature will.
Questions that arrive with this part number
The first is whether the BP and the BU are the same die. They are, and the difference is the package and the pin count. The second is whether the BP can be used at a gain of 1000 with the 50 kΩ resistor strapped by a 50 Ω resistor. It can, but 50 Ω of lead and trace resistance is 5 per cent of the gain term, so the resistor has to be placed at the pins rather than at the far end of a trace.
The third is whether a 5 V single supply works. It does not, because the supply range starts at 6 V and the reference pin has to sit above ground for a unipolar output. A rail to rail part from a newer family is the answer for a 5 V system, and it will not have the same bias current.
For a customer replacing an obsolete instrumentation amplifier with this grade, our amplifier cross reference page sets out the parameters to compare, and the drop in verification page lists the tests that catch a grade substitution.