DS26LV32ATMX-NOPB
Product Specifications
DS26LV32ATMX-NOPB
Texas Instruments — Power Management & Signal Chain
Product Overview
The DS26LV32ATMX-NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DS26LV32ATMX-NOPB: a discontinued 3.3 V RS-422 receiver
This page has to start with the status, because it decides everything else. The vendor addendum marks both rows behind this string as Obsolete, with a blank quantity and an instruction to call the vendor for the second row. There is no live production row for the DS26LV32ATMX-NOPB in the current addendum. What follows is therefore a description of what the part does, written so that a customer holding stock, or looking for a replacement, can match the function against a candidate.
The device is a quad differential receiver built on CMOS and run from 3.3 V, which meets both TIA/EIA-422-B and ITU-T V.11. It draws 9 mA typical and about 30 mW, takes four twisted pairs in and gives four single ended outputs at TTL and LVCMOS levels, and it fails safe: with the inputs open the output is high. The common mode range is 7 V at a 3 V differential input and 10 V at a 200 mV differential input, which is the widest window in the family and the reason it appears in industrial networks that see ground offsets.
The DS26LV32ATMX-NOPB rows as the addendum publishes them
| Part class | Quad differential line receiver, RS-422 and V.11 |
| Vendor status | Obsolete, no quantity published |
| Second row | Obsolete, part marking column reads see this string |
| Data sheet | SNLS128C, April 1999, revised February 2013 |
| Supply | 3.3 V, interoperable with 5 V RS-422 networks |
| Differential threshold | Minus 200 mV to plus 200 mV, 17.5 mV typical |
| Hysteresis | 35 mV typical at 1.5 V common mode |
| Common mode range | Minus 7 V to plus 7 V at a 200 mV differential |
| Input resistance | 5.0 kΩ minimum, 8.5 kΩ typical |
| Supply current | 9 mA typical, 15 mA maximum to 85 degrees |
| Power dissipation | 30 mW typical |
| Propagation delay | 6 ns minimum, 17.5 ns typical, 35 ns maximum |
| Skew between channels | 0.3 ns typical, 4 ns maximum |
| Rise and fall time | 4.1 ns and 3.3 ns typical, 10 ns maximum |
| Enable and disable | 40 ns maximum |
| Toggle frequency | 32 MHz |
| Output high | 2.4 V minimum at 6 mA sink |
| Output low | 0.13 V typical, 0.5 V maximum at 6 mA source |
| Tri state leakage | 50 µA maximum |
| ESD, human body | Above 6.5 kV |
| Failsafe | Output high on an open input |
| Body | SOIC, 16 pins |
| Temperature range | Minus 40 to plus 85 degrees industrial, wider on the military rows |
Notice what the obsolete status does and does not mean. It does not mean the die is gone from every warehouse, and it does not mean a customer's existing stock is unusable. It does mean that no new wafer starts are planned, so the supply is limited to what distributors hold and to whatever the vendor will build on a last time buy. Planning against this part without a last time buy is a schedule risk rather than a price risk.
What a replacement has to match
Four parameters define the function and all four have to be checked before a candidate is accepted. The first is the supply: a 3.3 V receiver cannot be replaced by the 5 V DS26C32AT without a rail change, even though the pin out matches. The second is the common mode range, because a part with a 7 V window replaced by one with a 5 V window will fail in a cabinet with a ground offset.
The third is the failsafe behaviour, which is not universal: some receivers leave the output undefined on an open input, and a protocol that relies on the idle high state will see framing errors. The fourth is the pin out, which follows the 26C32 family and is not the same as every quad receiver in a 16 pin body.
Where this receiver still sits
The part turns up in industrial serial ports, in motor drive control boards and in older telecom line cards, always as the receive half of a balanced pair. Its 32 MHz toggle frequency was generous when it was released and is modest now, which means a replacement at a higher speed is usually harmless as long as the input thresholds and the failsafe behaviour match.
Because the part is obsolete, the practical question is not what to buy but how many years of cover to hold. A last time buy sized on three years of forecast plus the service tail is the usual approach, and the tail is the part that gets underestimated on a product with a fifteen year field life.
Last time buy arithmetic
The quantity is the annual build rate times the number of years, plus the service spares rate times the field life, plus a scrap allowance for the reels that get damaged in storage. For a chassis product that ships 200 boards a year and stays in service for fifteen years, a hundred pieces a year of service demand over fifteen years is 1500 pieces, which is under one reel and therefore the smallest sensible buy.
Storage is the second half of the plan. A 3.3 V CMOS part in a sealed bag with desiccant holds its solderability for years, but the bag has to be intact and the storage temperature has to stay moderate. A reel kept in an uncontrolled warehouse for a decade will need baking and may still fail on wetting balance, which is why the buy is usually paired with a storage plan rather than left on a shelf.
Questions that arrive with this part number
The first is whether we can still supply it. The answer depends entirely on distributor stock on the day, and we quote what we can verify rather than what a listing claims. The second is whether a pin compatible 3.3 V receiver exists. Several do, and none of them is a drop in for every parameter, so the check has to be done on the four items above rather than on the pin count.
The third is whether the customer should move onto a 5 V part. That is a board change, and for a product in service it is usually more expensive than a last time buy, which is why so many obsolete interfaces stay in production long after the silicon has been discontinued.
Verification of stock is the step most buyers skip. A listing that shows a thousand pieces available may be a broker holding a photograph rather than a warehouse holding a reel, and for a discontinued part the difference matters. The checks that actually predict a usable delivery are the date code on the reel label, the country of origin against the vendor assembly site list, and a photograph of the label next to the reel. Where those three cannot be produced, the parts are a risk even when the price looks normal.
For a customer who must keep a line running, the alternative to a last time buy is a small board change that accepts a current production receiver. That change costs an engineering cycle and a qualification run, and it removes the supply risk permanently. The arithmetic usually favours the board change when the remaining product life is more than about five years and the annual volume is above a few hundred units.
A last point on the receiver itself: the 32 MHz toggle frequency and the 40 ns enable time are the two figures to check against a modern replacement, because a part that is faster everywhere else can still be slower on the enable path, and a bus that relies on a quick tri state release will show it as a collision on the first long cable run.
For a programme that has to cover this part, the obsolete part hub sets out the cross reference route, and the last time buy page covers the quantity calculation and the storage conditions.