Contact Us

INA103KU

Brand: Texas Instruments
Texas Instruments INA103KU is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA103KU — Power Management & Signal Chain | Superb Automation

INA103KU

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA103KU from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA103KU: the low noise amplifier in a surface mount body

The INA103KU is the 16 pin surface mount version of the INA103, published ACTIVE in a 40 piece tube and a 1000 piece reel. The electrical behaviour is the same as the plastic DIP part: 1 nV per root hertz of input noise, gain from 1 to 1000 set by one resistor or by pin strapping at 1 and 100, 800 kHz of bandwidth at a gain of 100, and 15 V per microsecond of slew rate. The surface mount body exists because the part is used in production quantities, and a through hole part in a modern build is a process cost rather than a technical choice.

The grade on this row is the commercial one, 0 to 70 degrees specified and minus 40 to 85 operating, the same as the DIP. There is no industrial or military grade of the INA103 in the current addendum, which is worth knowing before a customer specifies it into an outdoor product.

The INA103KU rows as the addendum publishes them

Part classLow noise instrumentation amplifier, surface mount
Vendor statusACTIVE, production data
Data sheetSBOS003A, revised September 2023
Gain range1 to 1000
Gain equationG equals 1 plus 6 kΩ divided by RG
Input noise at 1 kHz1 nV per root hertz
Total harmonic distortion0.0009 per cent at 1 kHz, gain of 100
Initial offset, KU grade250 µV plus 5000 µV divided by G
Common mode rejection, G equals 100100 dB minimum
Input impedance, differential60 Ω in series with 2 MΩ
Bandwidth at G equals 16 MHz
Bandwidth at G equals 100800 kHz
Slew rate15 V per microsecond
Output into 600 ΩPlus or minus 11.5 V, 40 mA
Capacitive load10 nF stable
Supply rangePlus or minus 9 V to plus or minus 25 V
Quiescent current9 mA typical, 12.5 mA maximum
Overload recovery1 µs from 50 per cent overdrive
BodySOIC, 16 pins, wide body
Tube rowINA103KU, 40 pieces, tube, Active
Reel rowINA103KU/1K, 1000 pieces, large tape and reel, Active
Moisture levelLevel 3 at 260 degrees, 168 hours floor life
MarkingINA103KU
Temperature, specified0 to plus 70 degrees

The KU offset row is the one to read carefully. The K grade in this family is specified at 250 µV plus 5000 µV divided by G, so at a gain of 100 the offset is 300 µV rather than the 42 µV of the KP row's typical figure. That is a grade difference inside the same data sheet, and it is the reason the two rows should not be treated as interchangeable on price alone.

Matching the source to the input

The 60 Ω differential input is the defining constraint. A 200 Ω microphone sees a 60 Ω load and loses a quarter of its open circuit signal, which the gain can recover, but a 10 kΩ bridge loses almost all of it. The rule is simple: use this part with sources under about 1 kΩ, and use the high impedance member of the family above that.

The balanced input is a genuine advantage for a microphone on a long cable, because the common mode noise that the cable picks up is rejected by the 100 dB of common mode rejection at a gain of 100, and the input is differential all the way to the first stage rather than after a pair of buffer amplifiers.

Working at 6 MHz

A 6 MHz bandwidth at unity gain means the part will amplify a fast pulse, but the settling time to 0.1 per cent at a gain of 100 is 1.5 µs, so a multiplexed system can switch channels every 2 µs. That is fast enough for audio and for a scanned bridge array, and it is not fast enough for a video signal, which is a different family.

At these frequencies the board matters. The gain resistor and its two traces form a loop with the internal 6 kΩ network, and a long loop adds inductance that appears as a peak in the response. Keeping the resistor within 5 millimetres of the pins and using a 0402 or 0603 body is the practical version of the advice.

Overload and recovery

The 1 µs recovery from a 50 per cent overdrive is what keeps a scanned system from losing a channel after a spike. A part without specified recovery can take milliseconds to return from saturation, and in a multiplexed system that shows up as a wrong reading on the channel after the overload rather than on the channel that caused it.

The output can deliver 40 mA into 600 Ω, which is enough to drive a cable or an ADC input with a resistive divider. A capacitive load up to 10 nF is stable without a series resistor, which covers most cable capacitances at short lengths.

Buying INA103KU

A 40 piece tube and a 1000 piece reel, both level 3. The reel suffix /1K is the quantity rather than a grade, and a purchase order written without it will not match. For a production build the reel is the normal carrier and the tube covers prototypes.

The commercial temperature grade is the constraint that decides whether this part can be used. An outdoor product needs minus 40 to 85 over the whole specification, and this row does not promise that, so the industrial alternative is a different part rather than a different suffix.

Questions that arrive with this part number

Whether the KU and KP rows are the same die is the first question, and they are the same function with different offset grades and different packages. The second is whether the gain of 100 can be set without an external resistor. It can, by strapping the gain pins, and that removes one error term from the chain at the cost of losing the ability to trim the gain.

The third is whether the part can run from a single 12 V supply. It can with a rail splitter, because the input and output ranges are referenced to the midpoint, and the reference pin allows the output to be offset. The supply current of 12.5 mA maximum then has to be added to the rail splitter's own draw.

The grade difference inside the family is the point to check before a specification is signed. The K grade at a gain of 100 carries 300 µV of offset where the P grade carries 42 µV, and the two rows sit on the same data sheet with the same noise figure, the same bandwidth and the same quiescent current. A customer who chose the family for its noise figure and then reads the offset from the wrong column will find the error at the first calibration run rather than at the quotation stage.

The gain strapping is worth using where the gain is fixed. A pin strapped gain of 100 removes the external resistor and its tolerance from the chain, and the remaining gain error is the internal 0.02 per cent typical. That is a better error budget than any 0.1 per cent resistor can deliver, and it costs nothing but two solder bridges. The strapping is read at power up from the pin state, so a link that is fitted after test changes the gain on the next power cycle and on every one after it.

A last point on the tube: 40 pieces at level 3 is a short window once opened, so a build that consumes fewer than forty parts a month should keep the tube in a dry pack between uses rather than leaving it on the bench.

For a production build that is moving from the DIP to the surface mount row, the amplifier cross reference page lists both, and the incoming inspection plan covers the grade marking check.