STM8S207R6T6
Product Specifications
STM8S207R6T6
ST — MCU & Embedded Processors
Product Overview
The STM8S207R6T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8S207R6T6: 32 Kbyte Flash STM8S MCU in LQFP64
STM8S207R6T6 is the 32 Kbyte Flash member of the STM8S 8-bit line in a LQFP64 body (14 by 14 mm), with 1024 bytes of true data EEPROM, 6 Kbyte of RAM, 52 general purpose I/O, 16 analog inputs and 16 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.
Order code and memory
| Order code | STM8S207R6T6 |
| Program Flash | 32 Kbytes |
| Data EEPROM | 1024 bytes, 300 kcycle endurance |
| RAM | 6 Kbytes |
| Package | LQFP64, 14 by 14 mm |
| Pin count | 64 |
| Maximum general purpose I/O | 52 |
| External interrupt pins | 36 |
| High sink outputs | 16 |
| ADC channels | 16 |
| Controller area network | not present |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 2.95 to 5.5 V |
| Maximum CPU clock | 24 MHz up to 105 C ambient |
| Flash access | zero wait states to 16 MHz |
| Core | Harvard, 3 stage pipeline, 80 instructions, 20 addressing modes |
| Timers | advanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer |
| Analog to digital converter | 10-bit, 16 channels, scan mode, analog watchdog, 14 clock cycles per conversion |
| ADC clock | 1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V |
| Serial interfaces | UART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz |
| Run current | 11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum |
| Low power | halt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off |
| Reset | power-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis |
| Identification | 96-bit unique ID, single wire interface module for debug and programming |
Points to check before this part goes on a BOM
The 64-pin body is where the full 16 channel ADC and the VREF+ and VREF- pins become available, so this is the smallest package in the line that can measure against a reference other than VDDA. It also carries 52 I/O and 36 external interrupt inputs, which is why 64-pin parts are often chosen for keypad and encoder front panels.
The EEPROM on this code is 1024 bytes, while the CAN equipped STM8S208R6 on the same 64-pin body carries 2048 bytes. Moving a product from the 207 to the 208 for CAN therefore also doubles the data EEPROM, and code that stores a configuration block by size will read more bytes than it wrote.
32 Kbytes of Flash with 6 Kbytes of RAM is an unusual ratio in this class, and it suits products that buffer a serial stream and run a small protocol stack while the program itself stays compact. The Flash endurance of 10 kcycles is the number to watch in a product that is reprogrammed in the field.
Where this order code fits
Keypad and display front panels, building controllers and instruments that need 16 analog inputs and a reference pin but do not need 128 Kbytes of program space. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete RF Part Replacement page. Both list the resource differences that decide the choice before any code is written.
Questions buyers ask
Does this package have VREF pins? Yes. VREF+ and VREF- are bonded on the 80 and 64-pin devices only, so the 64-pin R body can measure against an external reference.
How many external interrupts? 36 pins can trigger an external interrupt, spread over 6 vectors, so a matrix keypad can wake the part without polling.
Can I upgrade to CAN on the same footprint? The 208R6 is the CAN member on the same 64-pin body, but its data EEPROM is 2048 bytes against 1024 here and the silicon is a different order code, so both the firmware image and the production file change.
SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the Incoming Inspection Plan page walks through the checks that keep a substitute from failing on the bench.