AD8052ARZ-REEL7
Product Specifications
AD8052ARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8052ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8052ARZ-REEL7: 110 MHz on 4.4 mA, and the Input Range That Stops One Volt Below the Rail
The AD8052ARZ-REEL7 is a dual high speed voltage feedback amplifier in an 8-lead SOIC, with 110 MHz of gain bandwidth at unity gain, 145 V per microsecond of slew rate, 50 ns of settling to 0.1 percent, and 4.4 mA of supply current per amplifier. The output swings to within 25 mV of either rail and drives 45 mA, so it can push a video cable or a converter input; the input common mode range extends 200 mV below the negative rail and to within 1 V of the positive rail on a 5 V supply, which is the number that catches people. It runs on 3 V, 5 V or plus and minus 5 V, has 0.1 dB of gain flatness to 20 MHz at a gain of 2 into 150 Ohm, differential gain and phase of 0.03 percent and 0.03 degrees, and total harmonic distortion of minus 80 dBc at 1 MHz into 100 Ohm.
This is a general purpose high speed part with a rail to rail output and a not quite rail to rail input. It suits video buffers, active filters, converter drivers and clock buffers, all of which are in the data sheet's application list. The 4.4 mA per amplifier is what makes it usable in portable equipment, where a 15 mA video amplifier would dominate the budget.
One hundred and ten megahertz small signal is 23 MHz full power
The 110 MHz figure is a small signal bandwidth at unity gain. Limited by a 145 V per microsecond slew rate, a 2 V peak to peak sine reaches 23.1 MHz of full power bandwidth, and a 4 V peak to peak signal reaches half that. So a 50 MHz video signal at 1 V peak to peak is inside the slew limit and a 50 MHz signal at 4 V peak to peak is not, even though both are far below the 110 MHz bandwidth. The two numbers describe different measurements and only one of them is a limit on a real signal.
The 50 ns settling to 0.1 percent against a converter's acquisition window is the specification that matters in a data acquisition path. At 1 MSPS the window is 1 us, so 50 ns is a twentieth of it and the amplifier has room; at 10 MSPS the window is 100 ns and the settling is half of it, which is where the choice of amplifier starts to matter. Settling to 0.1 percent is 10 bits, and a 12-bit converter needs 0.024 percent, so the number has to be read with the resolution in mind.
| Bandwidth | 110 MHz at unity gain, 23.1 MHz full power at 2 V peak to peak |
| Slew rate | 145 V per us |
| Settling | 50 ns to 0.1 percent |
| Supply current | 4.4 mA per amplifier, 44 mW for the pair on 5 V |
| Output | Within 25 mV of either rail, drives 45 mA, 50 pF at unity gain |
| Input range | 200 mV below the negative rail, 1 V below the positive rail on 5 V |
| Video | 0.1 dB flatness to 20 MHz at a gain of 2, differential gain and phase 0.03 percent and 0.03 degrees |
| Distortion | Minus 80 dBc total harmonic at 1 MHz into 100 Ohm |
| Supply range | 3 V, 5 V, or plus and minus 5 V |
| Package | 8-lead SOIC, also MSOP for the dual, minus 40 C to 125 C |
The input range is the specification that decides the topology
On a 5 V supply the input common mode stops 1 V below the positive rail, which is 4 V, and extends 200 mV below ground. A unity gain buffer with an input that swings to 4.5 V therefore clips at 4 V, even though the output can reach 4.975 V. That asymmetry is common in parts with a rail to rail output and a limited input stage, and it changes the topology: a follower near the positive rail needs a different part or a level shift, and an inverting stage referenced to midscale is unaffected because its inputs sit at a fixed point.
The 45 mA output drive is a real current, not a short circuit figure. Into 100 Ohm it develops 4.5 V, which is the whole supply, so it is at the edge of what the part can do; into 150 Ohm it develops 6.75 V, which it cannot, so the practical load for full swing is above 150 Ohm. A video cable at 75 Ohm terminated at both ends presents 37.5 Ohm, where the part delivers 1.7 V of swing, and that is why video drivers are usually specified into 150 Ohm rather than into the cable impedance directly.
Two questions buyers ask
Is the dual a drop in for two singles?
Electrically it is the same amplifier twice, and the pinout is not: the single is an 8-lead part with different pin functions and the dual shares the supply pins between the two amplifiers. A board laid out for two singles does not accept the dual, and the dual saves board area rather than offering a substitution path.
Can it drive an ADC directly?
Yes, with a series resistor at the converter input. The 50 pF capacitive load rating at unity gain is the relevant number, and a converter's sampling capacitor plus the trace can approach it, so the resistor isolates the capacitance from the output stage. The settling figure of 50 ns to 0.1 percent is the one to check against the acquisition window, and the distortion at the signal frequency is the other.
Ordering and supply
The ARZ suffix is the 8-lead SOIC in tape and reel. Substitution traps are the input common mode range, the supply current and the settling time. A part with a rail to rail input and 15 mA of supply current is not a substitute in a portable product, and a part with the same bandwidth and 100 ns of settling loses a bit at 12 bits.
We hold and source this family for production and for repair. Start from the analog mixed signal ICs family page, compare a candidate against the amplifier cross reference, and where a substitute has to be qualified on a built board, the order in how to verify a drop in replacement puts the input range and the settling first.
Request Quote — In Stock, 100% New & Original, Full Warranty