Contact Us

LTC4311ISC6#TRPBF

Brand: Analog Devices
Analog Devices LTC4311ISC6#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTC4311ISC6#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LTC4311ISC6#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTC4311ISC6#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LTC4311ISC6#TRPBF: An I2C Accelerator for Buses That Have Outgrown 400 pF

The LTC4311ISC6#TRPBF is a dual I2C and SMBus active pull-up in a 6-lead SC70, built to keep a bus working when the capacitance goes past the 400 pF that the I2C specification assumes. It runs from 1.6 V to 5.5 V, operates to 400 kHz, and works by supplying a slew limited pull-up current during the rising edge instead of relying on a resistor alone. During the falling edge and at steady DC levels the current is disabled, which improves the falling edge and the low state noise margin. An automatic standby mode reduces supply current when both lines are high, disabled or unpowered the part does not load the bus at all, shutdown current is under 5 uA, and the pins are rated plus or minus 8 kV for human body model ESD.

The reason this part exists is arithmetic. A 1.5 kOhm pull-up against 400 pF has a 600 ns time constant, and the I2C fast mode rise time limit is 300 ns for the 0.3 to 0.7 of supply transition. A bus with 800 pF of capacitance, which is what eight or ten devices on a backplane produce, has a 1.2 us time constant and cannot meet the specification with any resistor that still allows the driver to pull the line low. Lowering the resistor makes the low level worse; the accelerator supplies current only while the line is rising, which is the asymmetry the bus needs.

What the slew limited current buys, in numbers

With 2 mA of pull-up current into 400 pF the rise rate is 5 V per microsecond, and the 0.3 of supply to 0.7 of supply window, 0.99 V on a 3.3 V bus, is crossed in 198 ns. That is inside the 300 ns fast mode limit with margin, where the 1.5 kOhm resistor needed 600 ns for one time constant and about 660 ns to reach 0.7 of supply. On an 800 pF bus the same current gives 396 ns, which is close to the limit, and above about 1 nF the bus needs a different approach: a bus buffer that splits it into segments rather than a stronger pull-up.

The part does not replace the resistors; it works with them. The resistors set the DC high level and the falling edge, the accelerator supplies the transient. A board that removes the resistors entirely and relies on the accelerator has no defined high level when the part is disabled, which is exactly the state a powered-down segment is in.

FunctionDual I2C and SMBus active pull-up
Supply range1.6 V to 5.5 V
Bus rateUp to 400 kHz
Bus capacitanceWell beyond the 400 pF specification limit
Rise time198 ns for 0.3 to 0.7 of a 3.3 V supply with 2 mA into 400 pF
StandbyAutomatic when both lines are high, under 5 uA in shutdown
Disabled behaviourDoes not load the bus when disabled or unpowered
ESDPlus or minus 8 kV human body model
Package6-lead SC70, or 2 mm by 2 mm DFN

Where an accelerator is the right answer and where it is not

An accelerator suits a single bus with too much capacitance: long traces across a backplane, several connectors, a ribbon cable to a front panel. It does not solve a bus with a genuine address conflict, a bus whose devices cannot arbitrate at the target rate, or a bus with a stuck line. Those are wiring and protocol problems, and a stronger pull-up makes a stuck line harder to see because the driver's sink current has to overcome the accelerator's source current.

The part also matters in a hot swap or power sequencing situation. A segment that is powered down must not load the rest of the bus, and the LTC4311 is specified not to, which means a card can be removed and the remaining bus keeps working at full rate. A plain resistor network on the removed card would not be a problem, but an accelerator on it would be if it loaded the bus while unpowered, which is why that line in the data sheet is worth checking before a board uses four of them on one backplane.

Two questions buyers ask

Can it increase the bus speed above 400 kHz?
No. It improves the rise time, which is one of the limits at 400 kHz, and the bus protocol and the device timings are the other limits. Fast mode plus at 1 MHz and high speed mode at 3.4 MHz have their own requirements, and an accelerator that meets the 400 kHz rise time does not make a 100 kHz device run at 1 MHz. Speed is set by the slowest device on the bus.

Does it work on a 1.8 V bus?
Yes, the supply range starts at 1.6 V, so a 1.8 V bus is inside it. The currents scale with the supply and the rise time arithmetic changes: the same 2 mA into 400 pF is still 5 V per microsecond, but the 0.3 to 0.7 window on 1.8 V is 0.54 V, crossed in 108 ns, so a low voltage bus has more margin than a 3.3 V one at the same capacitance.

Ordering and supply

The ISC6 suffix is the 6-lead SC70 in tape and reel. Substitution traps are the disabled state and the current. A part that loads the bus when unpowered breaks the hot swap case, and a part with a fixed strong pull-up instead of a slew limited one degrades the low level noise margin that the accelerator was supposed to improve.

We hold and source this family for production and for repair lots. Start from the analog mixed signal ICs family page, compare a candidate against the pin to pin cross reference, and where a substitute has to be proven on an existing backplane, the order in how to verify a drop in replacement includes the powered-down bus test.

Request Quote — In Stock, 100% New & Original, Full Warranty