LTC4416EMS#TRPBF
Product Specifications
LTC4416EMS#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC4416EMS#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTC4416EMS#TRPBF: Two Ideal Diodes, 25 mV of Drop, and 35 uA Per Channel
The LTC4416EMS#TRPBF is a dual PowerPath controller that drives two sets of external P-channel MOSFETs to make two near ideal diodes for power switchover. It operates from 3.6 V to 36 V, conducts with a typical 25 mV drop across the MOSFET, draws 35 uA per channel independent of load, protects against a reversed battery, and provides soft switchover between two sources so the output does not droop when the load moves from an adapter to a battery. The gate drive includes a clamp for MOSFET protection, and the package is a 10-lead MSOP.
The arithmetic that replaces a diode
A Schottky ORing diode at 5 A drops about 0.4 V and dissipates 2 W, which is heat inside an enclosure and voltage lost from the rail. The same 5 A through a MOSFET whose on resistance is 5 milliohms drops 25 mV and dissipates 125 mW, sixteen times less. The comparison is not only about loss: the 0.4 V drop means the downstream regulator needs 0.4 V more headroom, which on a 5 V rail at minus 5 percent is the difference between regulating and dropping out. That is the reason a controller plus two FETs replaces a diode pair even though it costs more parts.
| Supply range | 3.6 V to 36 V, covering one to eight lithium cells in series |
| Channels | Two, each driving an external P-channel MOSFET |
| Conduction drop | 25 mV typical, 125 mW at 5 A, against 2 W for a 0.4 V Schottky |
| MOSFET on resistance for 25 mV at 5 A | 5 milliohms |
| Quiescent current | 35 uA per channel, 306.6 mAh over a year for both |
| Switchover | Soft off, so the output does not droop between dissimilar source voltages |
| Fast response | Fast on above 25 mV of forward drop, fast off above 25 mV of reverse |
| Protection | Reverse battery, gate clamp, precision comparators for the switchover thresholds |
| Feedback | Open drain points for user defined hysteresis |
| Package | 10-lead MSOP |
Soft switchover and the droop question
When two sources of different voltage are ORed, the moment of transfer is the moment the output can dip. The controller ramps the gate of the incoming MOSFET rather than switching it, so the output capacitor is charged through a controlled resistance and the rail sags by a bounded amount instead of by the difference between the two sources. On a product with an adapter and a battery, that is the difference between a clean handover and a processor that resets when the adapter is plugged in.
The fast on behaviour is a small signal feature with a large effect: when the forward voltage across the MOSFET exceeds 25 mV the gate drive current increases dramatically, so the body diode conducts for a shorter time during a hot plug event. The fast off behaviour is the mirror image, detecting a reverse condition at 25 mV and turning the FET off before the reverse current builds. The 4416-1 variant differs in when fast off is enabled, which is a selection question rather than a performance difference.
Choosing the FET is most of the work
The controller is specified to drive large and small gate charge devices, so the FET choice is driven by the on resistance needed at the load current and by the gate charge the controller can move quickly. At 5 A and 25 mV the target is 5 milliohms, and a part that meets it at 25 C may be 8 milliohms at 100 C, which raises the drop to 40 mV. Two FETs in parallel halve both, at twice the gate charge and twice the board area, and the controller's gate drive has to be checked against that.
The 36 V ceiling covers eight lithium cells at 4.2 V, so the part sits in battery backup systems, uninterruptible supplies and emergency lighting. It does not cover a 48 V telecom bus, where a higher voltage member of the family is needed. Reading the input range against the highest source voltage rather than the nominal one is the check that avoids a part that works at 24 V and fails at 36 V with tolerance and a charging battery.
Two questions buyers ask
Can it replace two Schottky diodes directly?
Electrically yes, with two external FETs and their gate resistors, and the board area is larger than two diodes while the loss is much lower. The comparison to make is the thermal one: at 5 A the diode pair dissipates 4 W in the enclosure, and the FET pair dissipates 250 mW.
Does the switchover cause a reset?
The soft off ramp bounds the droop, but the output capacitor and the load current set the actual dip. A rail with little capacitance and a heavy load will still sag, so the capacitor is part of the switchover specification and not only part of the regulator's stability.
Ordering and supply
The LTC4416EMS#TRPBF is the MSOP, tape and reel, lead free code. The 4416-1 variant is a separate order code with a different fast off behaviour, so a reel of one is not a substitute for the other where the switchover timing has been characterised. The FETs are external, so the bill of materials also has to carry them and their gate components.
We hold and source this family for production quantities and for repair lots. Start from the family page for analog mixed signal ICs, check a proposed alternative against the power management cross reference, and if the controller and its FETs are holding a build the shortage route in BOM shortage recovery is where the pair is matched against the real load current.
Request Quote — In Stock, 100% New & Original, Full Warranty