STM8S105S4T6
Product Specifications
STM8S105S4T6
ST — MCU & Embedded Processors
Product Overview
The STM8S105S4T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8S105S4T6: 16 Kbyte 5 V STM8S access line MCU in LQFP44
STM8S105S4T6 is the 16 Kbyte member of the STM8S105 access line in a LQFP44 body (10 by 10 mm), with 1 Kbyte of true data EEPROM, 2 Kbytes of RAM, 34 general purpose I/O, 31 external interrupt inputs, 8 capture compare channels, 15 high sink outputs and 9 analog inputs. The supply range is 2.95 to 5.5 V, the core runs at up to 16 MHz with zero wait state Flash access, and the converter is 10 bit with its own reference pins.
Order code and memory
| Order code | STM8S105S4T6 |
| Program Flash | 16 Kbytes |
| Data EEPROM | 1 Kbyte, 300 kcycle endurance |
| RAM | 2 Kbytes |
| Package | LQFP44, 10 by 10 mm |
| Pin count | 44 |
| Maximum general purpose I/O | 34 |
| External interrupt pins | 31 |
| Timer capture compare channels | 8 |
| ADC channels | 9 of the 10 channel converter |
| High sink outputs | 15 |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 2.95 to 5.5 V |
| Maximum CPU clock | 16 MHz with zero wait state Flash access |
| Run current | 7.7 mA typical at 16 MHz from Flash on 5 V, 3.2 mA with the loop in RAM |
| Halt current | 6.5 uA typical at 5 V, 25 uA maximum at 85 C and 80 uA at 125 C |
| Active halt | wait, active halt and halt modes, with the auto wakeup unit |
| Low power modes | peripheral clocks can be switched off one by one |
| Wake up time | 7 microseconds from halt |
| Analog to digital converter | 10 bit, 9 channels, VREF+ and VREF- pins, 14 clock cycles per conversion |
| Digital to analog converter | not present |
| Comparators | not present on this line |
| Timers | one 16 bit advanced control timer with four capture compare channels and three complementary outputs, two 16 bit general purpose timers with five channels between them, one 8 bit basic timer, auto wakeup timer, window and independent watchdog |
| Serial interfaces | UART with LIN master, SmartCard and IrDA, SPI up to 8 Mbit/s, I2C up to 400 kHz |
| DMA | not present on this line |
| Data EEPROM endurance | 300 kcycle for the 1 Kbyte true data EEPROM |
| Program memory endurance | 10 kcycle, 20 years retention at 55 C |
| Identification | 96 bit unique ID, single wire interface module, option byte read out protection |
Points to check before this part goes on a BOM
This is the same 44 pin, 16 Kbyte device as the S4T6C with a shorter ordering string, and the difference is a trap for anyone matching a BOM from a drawing rather than from a packing list. ST ships both forms, the shorter string appears on older documentation, and an automated cross reference that treats the trailing letter as part of the memory or temperature field will flag the two as different parts when they are the same silicon. Stock checks should normalise the ordering string before comparing.
Electrically the part is the 5 V access line: 2.95 to 5.5 V, 16 MHz with zero wait state Flash, 2 Kbytes of RAM, 1 Kbyte of EEPROM at 300 kcycles, nine 10 bit converter channels and 15 high sink outputs on 34 port pins. The 10 by 10 mm body gives more copper area per pin than the 7 by 7 mm package, which helps when several high sink outputs drive LEDs continuously and the thermal path is the board itself.
For a product in production the practical question is usually availability rather than features, and this is a part where both order code forms circulate in the channel. When a shortage appears, the interchangeable check is the full string plus the date code, and the fallback is the C body on 48 pins if the board can take a 7 by 7 mm package, since the die is the same and only the bonded pins differ.
Where this order code fits
Production boards with an existing drawing that calls the short ordering string, relay and LED driver panels, and repair demand for equipment built around the 44 pin access line part. Teams comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and teams replacing a line that has gone end of life start from the Excess Inventory Management page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
Is S4T6 the same as S4T6C? Yes electrically. They are the same device with two forms of the ordering string; the trailing letter is not a memory, temperature or packing field, so both should be accepted against the same line item.
What is the difference from the K4? Package and pin count: 44 pins with 34 I/O and nine converter channels against 32 pins with 25 I/O and seven channels. Memory and core are the same.
Does it need an external crystal? No. The internal 16 MHz RC oscillator can clock the core, and the internal 128 kHz RC drives the watchdog and the auto wakeup unit, so a crystal is only needed when the application requires an accurate time base.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Obsolete RF Part Replacement page sets out the checks that keep a substitute from failing on the bench.