Contact Us

TPS22916BYFPR

Brand: Texas Instruments
Texas Instruments TPS22916BYFPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22916BYFPR — Power Management & Signal Chain | Superb Automation

TPS22916BYFPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22916BYFPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22916BYFPR: 2 A 5.5 V load switch with 60 milliohm on resistance and reverse current blocking

TPS22916BYFPR is a single channel load switch with a P channel pass FET, a smart pull down on the enable pin and always on reverse current blocking in a DSBGA (YFP) body of 4 pins. It switches a rail from 1 V to 5.5 V at up to 2 A with 60 milliohm typical at 5 V, and it uses 0.5 microamp while on and 10 nanoamp while off. The B version turns on in 115 microseconds at 5 V, which is the fast timing option, and the reverse current blocking circuit reacts within 10 microseconds when the output rises above the input.

Order code and package

Order code read outTPS22916 B YFP R: load switch TPS22916, B fast timing variant, YFP four pin wafer chip scale package, R large tape and reel
PackageDSBGA (YFP), 4 pins, 0.78 mm by 0.78 mm, 0.4 mm pitch, 0.5 mm height
Carrier in the vendor addendumTPS22916BYFPR at 3000 pieces on a large reel, marked BA over R; the same code with a small reel suffix carries 250 pieces
Moisture levelLevel 1, 260 degrees unlimited floor life
Lead finishSilver tin copper, quoted as SNAGCU, on a chip scale body with no wire bonds
Temperature gradeOperating free air minus 40 to plus 85 degrees
Absolute maximum6 V on the input, output and enable pins, with 2 kV of human body model ESD

Electrical parameters that decide the application

Input range1 V to 5.5 V, which covers a single lithium cell, a 3.3 V rail and a 5 V rail
Continuous current2 A maximum, limited by the package rather than by the FET
On resistance at 5 V60 milliohm typical and 80 milliohm maximum at 25 degrees, 100 milliohm maximum over the full range
On resistance at 1.8 V100 milliohm typical and 125 milliohm maximum at 25 degrees, 150 milliohm over the range
On resistance at 1 V200 milliohm typical and 275 milliohm maximum, the figure that decides whether a 1 V rail is usable
Quiescent current0.5 microamp typical and 1 microamp maximum while on, which is why the part suits always on rails
Shutdown current10 nanoamp typical and 100 nanoamp maximum on the B version, against 100 and 300 nanoamp on the L variants
Enable pin10 nanoamp of leakage when on, with a 750 kohm smart pull down that holds the pin low until the system drives it
Reverse current blockingActivates at minus 500 mA typical when the output exceeds the input, in 10 microseconds, and releases at 25 mV
Reverse leakage300 nanoamp maximum into the input with the blocking circuit active
Quick output discharge150 ohm from output to ground when disabled, fitted on the B version but not on the CN and CNL
Timing115 microsecond turn on at 5 V in the B version, against 1400 microseconds in the C version

Which suffix does what

TPS22916BYFPRfast turn on, 10 nanoamp shutdown, quick output discharge, active high enable
C versionslow turn on of 1400 microseconds at 5 V, chosen for a heavy capacitive load where inrush has to be limited
L versionsactive low enable, with a larger shutdown current of 100 nanoamp typical
CN and CNLthe slow timing versions without the quick output discharge, for a rail that must decay on its own
YFP bodythe 0.78 mm chip scale package, which is the only body offered for this family

Points to check before this part goes on a BOM

The reverse current blocking is always on and needs no enable or comparator, which is the feature that separates this part from a plain load switch. When the output is driven above the input by more than 25 mV the body diode path is closed within 10 microseconds and leakage falls to 300 nanoamp. On a board where a rail can be back fed by a charger, a hot plug event or a second supply, that behaviour is what keeps current from flowing backwards into a cell.

On resistance is quoted at four input voltages because it changes by a factor of three across the range. At 5 V the part is 60 milliohm and drops 120 mV at 2 A; at 1 V it is 200 milliohm and drops 400 mV at the same current, which is 40 percent of the rail. A board that uses the 5 V figure to justify a 1.2 V rail will find the load seeing about 0.8 V. The on resistance also rises with temperature, and the 100 milliohm maximum at 5 V is the number to use for a thermal or margin calculation rather than the typical.

The B version turns on in 115 microseconds and the C version in 1400 microseconds, and that difference is the whole reason both exist. A fast turn on into a large output capacitor produces an inrush limited only by the capacitor and the FET, which for a 10 microfarad load at 5 V is several amps for a short period. The C version spreads the same charge over a longer window and keeps the inrush inside the supply's capability. Choosing the fast part for a socket that drives a large capacitance is the most common application error with this family.

The smart pull down matters at power up, before any microcontroller is running. The enable pin is held low through 750 kohm, so the switch stays off until a real logic high arrives and does not float into a partially on state. Once the pin is driven high the pull down is disconnected to save the 10 nanoamp of leakage, which is why the on state current stays at half a microamp. A board that drives the pin from an open drain output should check that the high level is above the 1 V threshold at the worst case supply.

Shutdown current of 10 nanoamp on the B version against 100 nanoamp on the L versions sounds like a small difference and is a factor of ten in a battery product. A device that sits in storage for a year draws 0.09 milliamp hour through the B version and 0.9 milliamp hour through an L version, which for a 200 milliamp hour coin cell is under half a percent against four and a half. The active low enable of the L parts is often the real requirement, so the choice is usually made by the logic polarity and the leakage follows.

The quick output discharge of 150 ohm is fitted on the B version and left out of the CN and CNL. That resistor decides how a rail comes down: with it, a 1 microfarad output decays with a 150 microsecond time constant, and without it the rail holds its charge until the load bleeds it away. A build that resets a peripheral by cycling its supply needs the discharge, and a build that holds a memory rail up through a brief outage needs it left out.

Where this order code fits

Used to gate a sensor, radio or peripheral rail under firmware control in wearables, hearables, handheld terminals, asset trackers, portable instruments and any battery product where leakage in the off state decides shelf life. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

What happens if the output is driven above the input? The reverse current blocking circuit reacts within 10 microseconds at minus 500 mA and stops the reverse path, leaving 300 nanoamp of leakage. It releases when the output falls back within 25 mV of the input, so the switch returns to normal without a command.

Which version should be used for a large capacitive load? The C version, which turns on in 1400 microseconds at 5 V instead of 115 microseconds. The slower ramp limits inrush into the load capacitor and keeps the supply inside its own current limit.

Can the enable pin be left floating? It will stay off, because the smart pull down holds it low through 750 kohm. That is a defined state rather than a guarantee, and a board that relies on it should still fit a pull down or drive the pin.

How much current does it use when off? 10 nanoamp typical and 100 nanoamp maximum on the B version. The L variants are ten times higher, which matters on a coin cell that has to last a year in storage.

Is the part available in another package? No. The family is offered only in the 0.78 mm four pin chip scale body, so the land pattern is fixed and the assembly house needs to be able to place a 0.4 mm pitch part.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Kitting Service page sets out the checks that keep a substitute from failing on the bench.