Contact Us

TPS7A5301QRGRRQ1

Brand: Texas Instruments
Texas Instruments TPS7A5301QRGRRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A5301QRGRRQ1 — Power Management & Signal Chain | Superb Automation

TPS7A5301QRGRRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A5301QRGRRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A5301QRGRRQ1: automotive 3 A low noise regulator with a bias rail and wettable flank option

TPS7A5301QRGRRQ1 is a 3 A automotive grade low dropout regulator with 4.4 microvolt noise and a bias rail for low input operation in a VQFN (RGR) body of 20 pins. The output is adjustable from 0.8 V to 5.15 V with an external divider, dropout is 180 mV maximum at 3 A with the bias rail connected, and the part is qualified to AEC-Q100 grade 1 with a junction range to 150 degrees.

Order code and package

Order code read outTPS7A5301 Q RGR R Q1: automotive qualified, RGR 20 pin VQFN 3.5 mm by 3.5 mm, R tape and reel
PackageVQFN (RGR), 20 pins, 3.50 mm by 3.50 mm
Second bodyVQFNP (RTK), 20 pins, 4.00 mm by 4.00 mm, wettable flanks and a 12 ppm per degree mould compound for automotive inspection
QualificationAEC-Q100 grade 1, minus 40 to plus 125 degrees ambient, junction range to plus 150 degrees
ESDHBM classification level 2, CDM classification level C4A
Output capacitorceramic stable, 22 microfarad class recommended for the 3 A transient
Power goodopen drain output for sequencing and fault reporting

Electrical parameters that decide the application

Input voltage without bias1.4 V to 6.5 V
Input voltage with bias1.1 V to 6.5 V, which is the low input, low output case the bias rail exists for
Output voltage0.8 V to 5.15 V adjustable
Output current3 A
Dropout with bias180 mV maximum at 3 A, 170 mV typical
Dropout without bias310 mV maximum at 3 A
Output noise4.4 microvolts RMS, rising to about 11.7 microvolts RMS at a 5 V output across the band
Ripple rejection40 dB at 500 kHz, which is the switcher residue band
Accuracy1 percent maximum over line, load and temperature with the bias rail connected
Soft startcapacitor programmable, monotonic ramp for processor sequencing
Mould compoundthe RTK body uses a 12 ppm per degree compound, chosen so the package moves with the board rather than against it
GradeAEC-Q100 grade 1 covers minus 40 to plus 125 degrees ambient, with the junction allowed to reach 150

Family variants and how they differ

TPS7A5301-Q1the 3 A member on this page, adjustable 0.8 V to 5.15 V
RGR body20 pin VQFN 3.5 mm by 3.5 mm, the standard package for this order code
RTK body20 pin VQFNP with wettable flanks, chosen when automated optical inspection of the solder joint is required
Accuracy conditionthe 1 percent figure belongs to operation with the bias rail, without it the limit is looser
Gradegrade 1 ambient is 125 degrees, the junction may reach 150, and those are different numbers

Points to check before this part goes on a BOM

The 180 mV dropout figure needs the bias rail. Without it the maximum dropout at 3 A is 310 mV, so a 1.2 V output from a 1.5 V input has 300 mV to work with and only the biased case meets it. A radar or telematics board that leaves the bias pin floating has quietly given up 130 mV of headroom.

The 1 percent accuracy also carries the bias condition. That is the tightest number in the family and it is specified with the bias supply present. Without it the regulator still works across the wider input range, and the error budget has to be built from the looser limit rather than the headline figure.

3 A at 5 V to 1 V is 12 W, which no package survives. The part is meant for a low differential, typically 1.8 V to 1.2 V or 3.3 V to 2.5 V, where the dissipation stays near a watt. Automotive customers often ask for a 3.3 V to 1.8 V rail at 2 A, which is 3 W and already needs the wettable flank body on a multi layer copper pad.

Noise grows with the output voltage. The 4.4 microvolt RMS figure is at a low output, and the vendor's own curve gives about 11.7 microvolts RMS at 5 V and 8.3 microvolts at 3.3 V. A 5 V rail feeding an RF amplifier therefore starts from a higher floor than the front page suggests, and the post filter matters.

Grade 1 ambient and 150 degree junction are two different limits. A module that runs at 125 degrees ambient has only 25 degrees of junction rise available, which at 3 W of dissipation means a thermal resistance under 8 degrees per watt from junction to ambient. That is a copper and enclosure requirement, not a part requirement, and it is usually where an automotive build fails its first thermal test.

The wettable flank body exists for inspection, not for performance. On an automotive line the solder fillet on a QFN has to be visible to an optical inspection machine, and a plain QFN gives no fillet to look at. The RTK package adds the flank and a mould compound matched to the board's expansion, which reduces the shear stress on a large pad through thermal cycles.

Radar and telematics modules sequence several rails behind one another, and this regulator's power good output is the usual handoff. The flag releases when the output is inside regulation, so the next regulator starts only after this rail is valid. A board that instead ties several enables together and relies on the rails rising at the same rate will trip the processor's own sequencing monitor.

The bias rail has to be available before the regulator can start. In a module that runs from a 3.3 V housekeeping supply the bias pin is simple, and in one that starts from a battery the bias has to come from a rail that is already up. That ordering is a system decision, and it is the first thing to check when a board comes up in the wrong order. In a radar module the bias usually comes from the 3.3 V housekeeping rail, which is itself sequenced, so the two rails form a chain rather than two independent starts.

Where this order code fits

These parts power radar sensor modules, telematics units, infotainment head units and camera clusters, where a noisy pre regulator feeds a 3 A digital or RF rail and the whole assembly has to pass automotive qualification. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the RF Component Sourcing page.

Questions buyers ask

Is the wettable flank body a different part? It is the same silicon in an RTK package. The order code changes, and the reason to choose it is solder joint inspection on an automotive line, not electrical performance.

What happens if I tie the bias pin to the input? The part still regulates, but above a certain input the bias pin cannot supply enough gate drive and the dropout and accuracy numbers revert to the unbiased limits. Use a separate 3.3 V or 5 V bias when the input is close to the output.

Can it run at 150 degrees? The junction may reach 150 degrees under grade 1 ambient limits, but continuous operation there shortens life. Aim for a junction under 125 degrees where the application allows it.

What is the difference between the RGR and RTK order codes? Package only. RGR is the 3.5 mm VQFN, RTK is the 4 mm VQFN with wettable flanks. The silicon and the electrical limits are the same.

Where should the bias rail come from? From a rail that is already valid, usually 3.3 V or 5 V housekeeping. It only supplies gate drive, so its current is small, but it has to be present before the enable.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Medical Device Components page sets out the checks that keep a substitute from failing on the bench.