Contact Us

TPS7A8300RGWR

Brand: Texas Instruments
Texas Instruments TPS7A8300RGWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A8300RGWR — Power Management & Signal Chain | Superb Automation

TPS7A8300RGWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A8300RGWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A8300RGWR: 2 A, 6 microvolt noise regulator with pin programmed output

TPS7A8300RGWR is a 2 A low dropout regulator with very low noise and a pin programmed output that needs no feedback divider in a VQFN (RGW) body of 20 pins. The output is set from 0.8 V to 3.95 V by connecting pins, or up to 5.0 V with an external divider, dropout is 125 mV maximum at 2 A, and the noise is 6 microvolts RMS with 40 dB of rejection left at 1 MHz.

Order code and package

Order code read outTPS7A8300 RGW R: family, RGW 20 pin VQFN 5 mm by 5 mm, R tape and reel
PackageVQFN (RGW), 20 pins, 5.00 mm by 5.00 mm, thermal pad
Second bodyVQFN, 20 pins, 3.50 mm by 3.50 mm, the same die in a smaller outline
Operating temperatureminus 40 to plus 125 degrees Celsius
Output capacitor22 microfarad ceramic is the stated stable value, which is larger than most LDOs of this class
Bias rail1.1 V input operation requires it, the pin accepts up to 6.5 V
Power goodopen drain, usable for sequencing the load

Electrical parameters that decide the application

Input voltage without bias1.4 V to 6.5 V
Input voltage with bias1.1 V to 6.5 V
Output voltage, pin mode0.8 V to 3.95 V, set by pins with no resistor divider
Output voltage, resistor mode0.8 V to 5.0 V with an external divider
Output current2 A
Dropout125 mV maximum at 2 A
Output noise6 microvolts RMS across the audio and RF band
Ripple rejection40 dB at 1 MHz, which is where a switcher pre regulator leaves residue
Accuracy1 percent over line, load and temperature
Soft startcapacitor programmable, which limits the inrush into a large load capacitance

Family variants and how they differ

Pin mode0.8 V to 3.95 V in steps set by straps, no divider error, no feed forward capacitor
Resistor mode0.8 V to 5.0 V, needed above 3.95 V and the only way to get a 5 V rail
Body choice5 mm and 3.5 mm VQFN, same silicon, different thermal pad area
Siblingsthe same family covers lower current members with the same pin programming method
Negative railsnot covered by this family, a negative analogue rail is a separate device
Strap granularitythe pin mode steps in fixed increments, so not every voltage between 0.8 V and 3.95 V is reachable

Points to check before this part goes on a BOM

Above 3.95 V the pin programming stops working. A 5 V rail needs the resistor mode, and that brings back divider tolerance and a feed forward capacitor. Builds that assume the pin mode covers every output will find the 5 V variant is a different circuit even though the part number is the same.

The 22 microfarad output capacitor is part of the specification. Many regulators in this class are stable with 4.7 or 10 microfarad, and substituting a smaller capacitor because the board has little room leaves the loop with a phase margin that was never characterised. At 2 A the load transient also needs the charge, so the capacitor is doing two jobs.

125 mV maximum at 2 A is a maximum, which is unusual and useful. It means a 1.2 V output can be held from a 1.35 V input at full load, and a 1.8 V rail from a 1.95 V rail. The same 2 A at 3.3 V in and 1.2 V out is 4.2 W in a 5 mm body, which requires copper and airflow, so the low dropout figure is what makes the high current practical.

The bias rail unlocks 1.1 V input. Without it the input floor is 1.4 V, and a 1.2 V rail from a 1.3 V supply falls outside that. The bias pin needs a higher rail, usually 3.3 V or 5 V, so a board that has only a 1.2 V and a 1.8 V domain cannot use the low input mode at all.

Noise and rejection at 1 MHz are the reason to choose this part over a generic LDO. A 1 MHz switcher leaves residue right where the 40 dB figure applies, and the 6 microvolt broadband noise keeps that residue from turning into phase noise in a clock or converter. If the pre regulator switches at 500 kHz, check the rejection curve at that frequency rather than assuming the 1 MHz number.

The pin mode trades flexibility for accuracy. Each strap adds a fixed weight to the output, so the voltage lands on a grid rather than anywhere in the range. For the common rails, 0.9 V, 1.0 V, 1.2 V, 1.8 V and 2.5 V, the grid has a setting, and for an odd value like 1.15 V the resistor mode is the only route. Checking the grid before choosing the part saves a board revision.

The 3.5 mm body is not a smaller version of the 5 mm one for thermal purposes. Same die, less pad, so a 2 A load that sits comfortably in the larger body runs closer to the junction limit in the smaller one. The rail current is the same, the copper requirement is not.

The 40 dB rejection at 1 MHz is the reason this part exists, and it only pays off if the capacitor network does not undo it. A 22 microfarad ceramic at the load, a short connection to the regulator and a quiet ground reference are what preserve the rejection at that frequency. A long trace between the regulator and the load turns the rail into an antenna for the switcher it was meant to filter.

The pin mode grid covers the usual converter rails and stops short of the odd ones. 3.95 V is the ceiling, so 5 V needs the resistor mode, and a 4.2 V rail needs it as well. Checking which mode the target voltage needs is a one minute job that avoids a board with an unreachable setpoint. The grid also sets the resolution of a voltage trim, so a rail that has to be adjusted at test time needs the resistor mode even when the nominal value is on the grid.

Where this order code fits

The part powers high speed converters, SerDes lanes, clock generators, FPGAs and RF amplifiers in wireless infrastructure, test equipment and instrumentation, where a switcher feeds a rail that has to be quiet in the megahertz region. Teams comparing it with a neighbouring part start from our RF Component Sourcing page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.

Questions buyers ask

How do I set 5 V? With an external divider in resistor mode. The pin mode ceiling is 3.95 V, so 5 V is not reachable by strapping alone.

Can I use a 10 microfarad output capacitor? The part is specified with 22 microfarad. A smaller capacitor changes the loop and the transient response, and it is not covered by the published stability data.

What is the benefit of the bias pin? It allows a 1.1 V input instead of 1.4 V, which is what makes a 0.9 V or 1.0 V output possible from a 1.2 V rail at full current.

What is the difference between pin mode and resistor mode? Pin mode needs no external parts and has no divider error, and it stops at 3.95 V. Resistor mode reaches 5.0 V and brings back divider tolerance and a feed forward capacitor.

Why does the part need 22 microfarad when others need 4.7? The loop was characterised with 22 microfarad and the 2 A transient needs the charge. A smaller capacitor moves the loop and reduces the transient margin.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Amplifier Cross Reference page sets out the checks that keep a substitute from failing on the bench.