Contact Us

UCC28780DR

Brand: Texas Instruments
Texas Instruments UCC28780DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC28780DR — Power Management & Signal Chain | Superb Automation

UCC28780DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC28780DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC28780DR: active clamp flyback controller for zero voltage switching up to 1 MHz

UCC28780DR is a flyback controller that clamps the primary leakage energy and uses it to achieve zero voltage switching on the primary FET in a SOIC (D) body of 16 pins. It runs up to 1 MHz and supports both silicon and gallium nitride switches through programmable timing, with full or partial zero voltage switching controlled adaptively. Brownout detection works without a direct line sense, and the over power protection is programmable, which is how a peak power mode is supported inside a rated envelope.

Order code and package

Order code read outUCC28780 D R: device UCC28780, D sixteen pin SOIC, R large tape and reel
PackageSOIC (D), 16 pins, with a 16 pin WQFN alternative under the RTE code
Carrier in the vendor addendumUCC28780DR at 2500 pieces on a large reel, 40 piece tubes for the same body, and the RTER package at 3000 pieces
Moisture levelLevel 1, 260 degrees unlimited floor life
Lead finishNickel palladium gold
Operating temperatureminus 40 to plus 125 degrees
Absolute maximum38 V on the supply, 38 V on the switch source pin, 25 V on the gate drive pins

Electrical parameters that decide the application

Supply turn on17.5 V typical, within 16.7 to 18.2 V, with turn off between 9.35 and 10.4 V
Run current2.3 to 3.3 mA depending on state, quoted with and without switching
Start current400 to 550 uA in the start state, which is what the bias resistor chain has to supply
Fault current265 to 350 uA in the fault state, low enough to keep a hiccup restart economical
Switching frequencyUp to 1 MHz, set by the timing resistors and the resonant period
Current sense threshold765 to 825 mV maximum, which sets the primary peak current
Zero crossing detection10 to 55 mV threshold on the switch source pin, with a 2.2 us timeout
Propagation delay20 to 45 ns from zero crossing detection to gate high, which is what keeps the timing inside the resonant window
Gate driveSeparate high side and low side outputs, programmable timing for silicon or GaN devices
BrownoutDetected without a direct line sense, from the reflected output voltage and the switching behaviour
ProtectionsOver temperature, output overvoltage, output short circuit, overcurrent and pin fault
Adaptive behaviourZero voltage switching is tracked at full and partial load, with a multimode control law chosen from the input and output conditions

Family members and how they differ

UCC28780the part on this page, active clamp flyback with adaptive zero voltage switching
SOIC and WQFN bodiesthe D package at 2500 pieces on a reel and the RTE package at 3000, same die
Silicon or GaN outputset by external timing components rather than by a suffix, so one order code covers both switch types
Against a plain flyback controllerthe clamp winding and the clamp capacitor replace the lossy snubber, and the leakage energy is recovered instead of burned
Against an LLCa flyback holds regulation over a wider input range without a PFC front end, at a lower power level

Points to check before this part goes on a BOM

The active clamp is not a snubber. A conventional flyback burns the leakage inductance energy in an RC or RCD network on every cycle, and at 1 MHz that loss becomes the dominant term. This controller turns on a small clamp switch to capture that energy in a capacitor and then releases it to help the primary FET commutate, so the same energy that was waste becomes the mechanism for zero voltage switching.

Programmable timing is what makes one order code serve silicon and gallium nitride. The two switch types need very different turn on and dead time windows, and a GaN device with a 6 V gate cannot be driven by a 12 V timing set. Two resistors and the clamp capacitor value move the controller from one to the other, which is why the part is described as supporting both rather than having a separate GaN suffix.

Brownout detection without a direct line sense removes an isolation barrier component. The controller infers the input condition from the reflected output voltage and from how the converter behaves at the current limit, so a brownout is detected on the secondary side without an optocoupler or a high voltage divider chain. The trade is that the detection depends on the transformer turns ratio being known and stable.

The programmable over power protection is what allows a peak power mode. Many adapters have to deliver twice their rated power for a short window, for example while a motor starts or a laptop charges and runs at once. Setting the over power threshold above the continuous rating but with a time limit lets the converter use the thermal mass of the transformer for that window, and then fall back without latching off.

The 2.2 microsecond zero crossing timeout is a protection, not a tuning parameter. If the switch source pin does not cross within that window the controller stops waiting and switches anyway, which prevents a stall when the converter runs at very light load or when the resonant period shifts with temperature. A bench measurement of the actual zero crossing time at the lowest load is the way to confirm that the timeout is not being reached in normal running.

Where this order code fits

Used in high density AC to DC adapters that must meet DoE Level VI and CoC Tier 2: laptop and tablet chargers, USB PD adapters, TV and monitor power boards, LED drivers and instrument supplies where the height limit rules out an LLC with its larger resonant inductor. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Can it drive a gallium nitride switch? Yes. The timing is programmable, and the vendor states direct operation with a GaN driver and GaN FET using logic level gate signals. The external timing components have to be set for the GaN window rather than reused from a silicon build.

What switching frequency can be reached? Up to 1 MHz. The practical ceiling is set by the transformer and the switch losses rather than by the controller, and the vendor's typical application runs well below the maximum.

Does it need a line sense for brownout? No. Brownout detection works without a direct line sense, which removes a high voltage divider or an optocoupler from the isolation barrier. The transformer turns ratio becomes part of the detection accuracy.

What is the difference between the D and RTE packages? The body only. The SOIC is 2500 pieces on a reel and the WQFN is 3000, with the same controller inside. The choice is about thermal pad and board space.

How is peak power handled? Through the programmable over power protection. The threshold is set above the continuous rating and the controller limits how long the converter can stay there, so a short peak is supported without latching the supply off.

Does it need a clamp capacitor on the primary? Yes, the active clamp is formed by the clamp switch inside the control loop and an external capacitor across the primary winding. Its value sets the resonant period that the timing resistors are matched to, so the two are chosen together.

Is a snubber still needed across the primary? No, the clamp replaces it. The leakage energy that a snubber would burn is captured by the clamp capacitor and reused for commutation, so an RC network across the winding only adds loss and shifts the resonant period the timing was set for.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.