Contact Us

STM8L101K3T6

Brand: ST
ST STM8L101K3T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8L101K3T6 — MCU & Embedded Processors | Superb Automation

STM8L101K3T6

ST — MCU & Embedded Processors

Product Overview

The STM8L101K3T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8L101K3T6: 8 Kbyte ultra-low-power STM8L101 MCU in LQFP32

STM8L101K3T6 is an 8 bit ultra-low-power part in a LQFP32 body (7 by 7 mm) with 8 Kbytes of Flash, up to 2 Kbytes of that array usable as data EEPROM, 1.5 Kbytes of RAM and 28 port pins. The core runs at up to 16 MHz from a 1.65 to 3.6 V supply, there is no analog to digital converter, and the analog work is carried by two comparators with four inputs each. Halt current is 0.3 uA and active halt 0.8 uA, which is the lowest sleep current in the STM8L family.

Order code and memory

Order codeSTM8L101K3T6
Program Flash8 Kbytes, shared with the data area
Data EEPROMup to 2 Kbytes taken from the same array
RAM1.5 Kbytes
PackageLQFP32, 7 by 7 mm
Pin count32
Maximum general purpose I/O28
Analog to digital converternot present
Comparators2 with 4 inputs each
Temperature gradesuffix 3, minus 40 to plus 125 C

Electrical and peripheral parameters

Supply voltage1.65 to 3.6 V
Maximum CPU clock16 MHz, 16 MIPS peak
Run currentabout 150 uA per MHz
Halt current0.3 uA typical
Active halt0.8 uA typical with the auto wakeup unit running
Low power modesthree low power modes, wait, active halt and halt
Wake up timeabout 4 microseconds from the internal 16 MHz RC start up
Analog to digital converternot present
Digital to analog converternot present
Comparators2, each with four inputs and a shared reference, both can wake the core
Timerstwo 16 bit general purpose timers with two channels each, one 8 bit timer, beeper timer, auto wakeup unit, independent watchdog
Serial interfacesSPI, I2C, USART
DMAnot present on this line
Data EEPROM enduranceup to 2 Kbytes taken from the Flash array, 300 kcycle
Program memory endurance20 years retention at 55 C
Identification96 bit unique ID, single wire interface module, in circuit emulation

Points to check before this part goes on a BOM

The K3 is the same 8 Kbyte die as the F3 in a 32 pin LQFP body, which raises the usable port count to 28 and adds the pins needed for a parallel keypad, a second comparator input pair and a hardware debug header that does not have to share a functional pin. Nothing else changes: no converter, 1.5 Kbytes of RAM, up to 2 Kbytes of EEPROM taken from the Flash array, and the same 0.3 uA halt and 0.8 uA active halt figures.

Because the die has no ADC, the two comparators carry the analog work, and each has four inputs with a shared reference, so a window detector, a level switch or a zero crossing sensor can be built with resistors and no converter. The comparator outputs can also wake the core from halt, which is how a battery product reacts to an event without running a timer at high frequency. That is the classic L101 use case and the reason the line still ships in large volumes.

The serial set is one SPI, one I2C at 400 kHz and one USART with a fractional baud rate generator, plus an infrared interface and a beeper timer. On 28 pins that is enough to be a small node on a bus while still driving a display of discrete LEDs and a handful of keys. The limit is code space: 8 Kbytes shared with up to 2 Kbytes of EEPROM leaves a 6 Kbyte image, which on this core is roughly 4000 lines of C after the startup code and the library.

Where this order code fits

Building bus nodes, room controllers, LED panel drivers, infrared remote receivers and battery products that need more pins than a 20 pin body allows but no converter. Teams comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and teams replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Is the K3 pin compatible with the L151K4? The two families share a pinout philosophy and the L151 is listed as pin to pin compatible with the L101, but the L151 adds the converter and the VREF pins, so a board built for the K3 needs its analog pins re checked before an L151 can drop in.

How many comparators are there? Two, each with four inputs and a shared reference, both able to wake the core from halt. There is no ADC on this line.

What is the run current? About 150 uA per MHz from a 1.65 to 3.6 V supply, with 0.8 uA in active halt and 0.3 uA in halt, which is the lowest sleep current in the STM8L family.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.