STM32L152VBT6
Product Specifications
STM32L152VBT6
ST — MCU & Embedded Processors
Product Overview
The STM32L152VBT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32L152VBT6: 128 Kbyte, LQFP100 body
STM32L152VBT6 is a member of the STM32L151x6/8/B and STM32L152x6/8/B low power line described by DocID17659 Rev 12. The order code fixes 128 Kbytes of Flash, 16 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 83 general purpose I/O and 24 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down supply.
Order code and memory
| Order code | STM32L152VBT6 |
| Program Flash | 128 Kbytes |
| SRAM | 16 Kbytes |
| Data EEPROM | 4 Kbytes with ECC |
| Package | LQFP100, 14 x 14 mm, 100 pins |
| Maximum general purpose I/O | 83 |
| Analog input channels | 24 channels on the 12 bit converter |
| Digital to analog converter | 2 channels of 12 bits |
| Segment LCD driver | 4x44 or 8x40 segments |
| Supply voltage | 1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down |
| Maximum CPU clock | 32 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient |
| Datasheet | DocID17659 Rev 12 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 32 MHz, 1.25 DMIPS per MHz, memory protection unit |
| Clock sources | 1 to 24 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC trimmed to plus or minus 1 percent, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC, and a PLL that also produces the 48 MHz USB clock |
| Low power modes | 214 microamps per MHz in Run mode, 9 microamps in Low power run, 1.2 microamps in Stop with the RTC, 0.9 microamps in Standby with the RTC and 10 nanoamps of I/O leakage, with wakeup from Stop under 8 microseconds |
| Timers | ten timers: six 16 bit timers with up to four compare channels each, two 16 bit basic timers and the independent and window watchdogs, plus the SysTick counter and the RTC |
| Serial interfaces | two SPI blocks at 16 Mbit/s, two I2C blocks with SMBus and PMBus, three USARTs with ISO 7816 and IrDA support and one USB 2.0 device port clocked from the internal PLL |
| Analog | one 12 bit ADC at 1 Msps, two 12 bit DAC channels with output buffers and two ultra low power comparators that double as a wakeup source, with capacitance sensing on up to 20 channels |
| Memory interface | not present on this body |
| Flash and EEPROM endurance | program memory rated 10 kcycles minimum over minus 40 to plus 105 C with 300 kcycles typical, EEPROM 30 kcycles minimum with 300 typical, and 30 years of retention at 85 C against 10 years at 105 C |
| Thermal resistance junction to ambient | 46 C/W on LQFP100 |
| Input tolerance | 5 V tolerant on 73 of the 83 I/O of the 100 pin body, all mappable on 16 external interrupt vectors |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | the VBAT domain keeps the RTC and the backup registers alive with the main rail off |
| Status | full production per the datasheet cover |
Points to check before this part goes on a BOM
The order code is V for 100 pins, B for 128 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. The 100 pin body is the first one in this document that bonds out port E, and that is where the extra 32 I/O over the 64 pin body come from.
83 general purpose I/O leaves 17 pins for supply, ground, reset, the crystal, the boot select and the reference pins. On a controller with 40 digital signals, 24 analog channels and a glass display the pin budget is the decision, and it is the reason buyers stay on the 100 pin body rather than adding an expander.
The display driver covers 4x44 or 8x40 segments, that is 176 or 320 segments on 48 pins. A process controller with setpoint, measured value, bar graph and alarm annunciators fits the 8x40 arrangement, which is the same capability the STM32L152xC and xD documents carry.
The LQFP100 is rated 46 C/W junction to ambient, so 435 mW at an 85 C ambient against a 105 C junction. That is slightly worse than the 64 pin body on paper because of the larger lead frame, and the practical answer is the copper area the board gives the part rather than the package choice.
24 analog channels share the ports with the display lines. The ADC is the same 1 Msps 12 bit converter as the smaller bodies, so the larger package buys inputs and not resolution, and a board that needs 16 bit measurements is looking at a converter outside this family.
1.2 microamps in Stop with the RTC and 0.9 microamps in Standby are the two figures that matter for a panel instrument left powered from a battery backed rail. The 83 I/O and the display driver cost nothing in those modes because the pins are reconfigured before the part enters them.
The BGA100 body carries the same die and the same memory, and the order code for it ends in H rather than T. On a board with limited height the BGA version is the reason to keep the 100 pin pinout, and the thermal resistance is worse there because the balls sit under the package rather than around it.
The step up to 256 Kbytes in the 100 pin body is STM32L152VCT6 in the xC document, which adds 32 Kbytes of SRAM and 8 Kbytes of EEPROM and moves the step-up converter for the glass into the part. The step down is RBT6, which gives up port E and the wide display to save board area.
Where this order code fits
It is the wide body member with the largest glass driver, so it fits panel meters, industrial controllers and analysers that show a full segment display and still expose port E. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
How many segments can the glass driver handle? 176 segments in the 4x44 arrangement or 320 in the 8x40 arrangement, using 48 pins. The 8x40 mode needs a bias network matched to the glass and is what a full annunciator panel uses.
Does port E exist on the 64 pin body? No. Port E is bonded out from the 100 pin body upward, so the 83 I/O figure belongs to this package and the 64 pin body carries 51.
What is the difference between the T and H suffix? T is the LQFP body, H is the BGA body. The die, the memory and the pinout are the same, so the choice is assembly capability and height rather than function.
How much SRAM does the part carry? 16 Kbytes. The 256 Kbyte code in the xC document carries 32 Kbytes and the 384 Kbyte code in the xD document carries 48 Kbytes, both in the same 100 pin footprint.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.