AMC7820Y/250
Product Specifications
AMC7820Y/250
Texas Instruments — Power Management & Signal Chain
Product Overview
The AMC7820Y/250 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AMC7820Y/250: eight analog inputs, three DACs and nine op amps in one package
AMC7820Y/250 is an analog monitoring and control circuit in a 48 pin TQFP, supplied on a 250 piece tape and reel. It contains an 8 channel 12 bit ADC sampling at 100 kHz, three 12 bit DACs, nine operational amplifiers, a thermistor current source, an internal 2.5 V reference and an SPI port. On a single 5 V supply it dissipates about 40 mW.
That combination is unusual now and was normal when the document was written in 2002. It exists because a laser controller or an optical amplifier needs to read eight slow analog points, drive three bias settings and buffer a handful of signals, and doing that with discrete parts costs more board area than the whole integrated circuit.
The /250 suffix is the reel size, not a grade. The same device ships as AMC7820Y/2K on a 2000 piece reel, and the two are the same silicon in the same PFB body. The figures below come from SBAS231B and from the package and ordering section at the back of the document.
What is actually inside the package
The ADC is a 12 bit successive approximation converter with an 8 channel multiplexer in front of it and a 100 kHz sampling rate. The unbuffered input range is 0 V to 5 V; the buffered common mode range is 0 V to 3.8 V, which is the number that matters when the source has any impedance at all. That asymmetry is the first thing to check against a sensor list.
The three DACs are 12 bit and their output range is 0 V to 2.5 V or 0 V to 5 V, selectable. The nine operational amplifiers are uncommitted, which means they can be used as buffers, as gain stages or as active filters, and they are the reason the part survives in circuits where the ADC alone would not be enough.
The thermistor current source delivers up to 1 mA and is intended to excite a thermistor in a laser or an optical module. Combined with one ADC channel and one of the op amps, it makes a complete temperature measurement without any external active parts.
| Function | analog monitoring and control circuit |
| ADC resolution | 12 bits |
| ADC channels | 8, through an input multiplexer |
| Sampling rate | 100 kHz |
| ADC input range | 0 V to 5 V unbuffered, 0 V to 3.8 V buffered common mode |
| DAC resolution | 12 bits, three channels |
| DAC output range | 0 V to 2.5 V or 0 V to 5 V |
| Operational amplifiers | nine, uncommitted |
| Thermistor source | up to 1 mA |
| Reference | internal 2.5 V, external reference input available |
| Interface | SPI, 3 V logic compatible |
| Supply | single 5 V |
| Power dissipation | 40 mW typical |
| Package | TQFP, PFB body, 48 pins |
| Carrier | 250 pieces on a tape and reel, or 2000 in the 2K option |
| Operating range | minus 40 to plus 85 degrees Celsius |
The 85 degree ceiling is the constraint that decides the socket
Minus 40 to plus 85 is a commercial industrial window, not an extended one. On a laser bench or inside a rack mounted optical amplifier that is plenty. On a module that sits next to a pump or in an enclosure with no airflow it is not, and the part that was chosen at the bench fails the thermal survey at the system level.
That is worth saying plainly because the applications list makes the part look more rugged than it is. Laser current control and thermoelectric cooler control both involve power dissipation nearby, and the local ambient can be ten degrees above the rack ambient. A board that measures 80 degrees at the package in a 25 degree room has no margin at all.
The dissipation of the part itself is small, 40 mW, so the rise is dominated by the board and the neighbours. That is a board level problem, and the answer is copper and airflow rather than a different package.
The SPI port, the reference and the sequencing
The SPI port is a plain four wire interface with a chip select, and it is fast enough to read all eight channels inside one control loop iteration. The converter is 12 bits and the sampling rate is 100 kHz, but the multiplexer settling time is what limits a scan of eight channels: each channel change needs the input capacitance of the converter to charge through the source impedance, and a high impedance sensor needs either a buffer or a longer settle.
The nine uncommitted amplifiers exist partly to solve that. A source with more than a few kilohms of impedance is buffered by one of them, and the buffer's own offset then becomes part of the channel error. That is a known and bounded term, and it is cheaper than adding eight external buffers.
The internal reference is 2.5 V and can be overridden by an external one. On a laser controller the reference usually comes from a precision source shared with the current loop, because the DAC setting and the measured current have to be on the same scale. Using the internal reference and a separate external reference for the current loop creates two scales that drift against each other, and the calibration then depends on which one was used.
Where this part still earns its place
The document lists continuous wave laser and pump laser current control in dense wavelength division multiplexing, thermoelectric cooler current control, optical power monitoring and tunable lasers. The common structure is a rack unit with several optical subassemblies, each needing a bias, a temperature and a power reading.
An erbium doped fibre amplifier is the classic case. It needs pump laser current control, a thermistor reading at the pump, a photodiode reading at the input and the output, and a variable optical attenuator setting. That is three or four analog inputs, two outputs and a handful of buffers, which is exactly the mix this part carries.
Test equipment is the other place we see it. A bench instrument with eight slow monitoring points and three control outputs uses the same building blocks, and the 12 bit resolution is enough because the accuracy of the surrounding references is the limit rather than the converter.
Our ADC DAC cross reference page covers the converters we hold against this function, and the component obsolescence management page describes how a 2002 vintage part is handled when the wafer fab moves and the reel date codes start to age.
The other detail that decides a build is the package. A 48 pin TQFP at 0.5 mm pitch is at the edge of what a low cost assembly line can place without an X-ray check, and a board that also carries fine pitch BGAs will have the TQFP inspected anyway. On a build where this is the finest pitch part, the inspection plan can be lighter, and that is a real cost difference on a small volume.
The 250 piece reel is the second cost item. A prototype that needs twenty parts still buys a reel, and the reel is small enough that the remainder is usable on the next build rather than becoming shelf stock. That is the opposite of the AMC1200 situation, where the small reel is a consequence of a wide body and the parts are consumed quickly.
Three questions buyers ask about this string
Is the 250 a grade or a quantity? A quantity. The reel holds 250 pieces; the 2K option holds 2000. Same device, same body.
Can the nine op amps be used as a filter? Yes, they are uncommitted and the document prints their bandwidth and slew rate. They are not rail to rail, so a filter that needs to swing to the rails needs a different part.
Is the part still active? The document is from 2002 and the addendum still prints both reel options as production. That is a good sign but not a guarantee, and for a ten year build we would ask for a written lifecycle statement before committing.