TMP236A2DCKR
Product Specifications
TMP236A2DCKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMP236A2DCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMP236A2DCKR: 19.5 mV per degree from a three terminal analog sensor
TMP236A2DCKR is the SC70 member of the TMP23x analog temperature family. It puts out a voltage that rises 19.5 mV for every degree Celsius, with 400 mV at 0 degrees, and it needs no register write, no clock line and no address. On a board where the temperature reading has to survive a firmware crash, a supply brownout or a dead I2C bus, that property is worth more than a digit of resolution.
The part is specified from minus 10 to plus 125 degrees Celsius with a maximum error of 2.5 degrees over that window and typically 0.5 degrees between 0 and 70 degrees. It draws 9 microamps at 25 degrees on a 3.1 V rail and 14.5 microamps maximum across the window, and it powers up in 800 microseconds, which is short enough to switch the sensor on, take a reading and switch it off again inside a duty cycled node.
The numbers below come from SBOS857E, revised May 2019, and from the package option addendum at the back of that document. They are the figures we check against a customer BOM before a quotation goes out, and they are the ones an incoming inspection plan should sample, because the two failure modes that matter on this family are a wrong gain grade and a body that does not match the footprint on the board.
What the DCK body and the A2 grade mean
The DCK suffix is the 5-pin SC70 body, 2.00 mm by 1.25 mm, and the R at the end of the order code is the large tape and reel. Compared with the 3-pin SOT-23 member of the same family, the SC70 version keeps two pins that the SOT-23 does not have: pin 1 and pin 3 are marked NC in the pin table and may be left floating or tied to ground. That sounds like a waste of two pins until a board already carries an SC70 land for a different sensor and the question is whether the TMP236 can drop into it.
The A2 grade is the tighter of the two accuracy levels. The family prints A2 as 0.5 degrees typical and A4 as 1 degree typical, and the maximum error columns follow the same split. A reel marked A2 that measures like an A4 part is a counterfeit symptom worth sampling for, and it is the first thing we check when a customer forwards a reel bought elsewhere.
| Function | analog output temperature sensor, positive slope |
| Sensor gain | 19.5 mV per degree Celsius, 400 mV at 0 degrees |
| Specified range | minus 10 to plus 125 degrees Celsius |
| Maximum error | 2.5 degrees over the specified window, 0.5 degrees typical from 0 to 70 |
| Supply range | 3.1 V to 5.5 V, 6 V absolute maximum |
| Supply current | 10 microamps typical at 25 degrees on 3.1 V, 14.5 microamps maximum |
| Power-on time | 800 microseconds typical |
| Output drive | 500 microamps maximum, stable into 1000 pF |
| Output protection | short circuit protected, output range minus 0.3 V to VDD plus 0.3 V |
| Line regulation | 0.02 mV per volt typical, 0.1 mV per volt maximum |
| Long term drift | printed in the application section, not a datasheet limit |
| Package | SC70-5, DCK, 2.00 mm by 1.25 mm |
| Thermal resistance | 275 degrees per watt junction to ambient in the SC70 body |
| ESD | plus or minus 4000 V human body, plus or minus 1000 V charged device |
| Junction limit | 150 degrees absolute maximum |
| Carrier | 3000 pieces on a large reel |
| Moisture level | level 1 at 260 degrees, unlimited floor life |
Output transfer and what an ADC sees
The transfer is a straight line: 400 mV at 0 degrees plus 19.5 mV per degree. At 25 degrees the output is 887.5 mV, at 50 degrees it is 1.375 V, at 85 degrees 2.0575 V and at 100 degrees 2.35 V. The top of the specified window lands at 2.8375 V, which is why the supply floor is 3.1 V rather than the 2.3 V used by the TMP235 member: the output stage needs headroom above its own full scale value.
That arithmetic decides how the sensor is read. A 12-bit converter running on a 3.3 V reference resolves 0.806 mV per count, which is 0.041 degrees per count, far finer than the 2.5 degree accuracy of the part. A 10-bit converter on the same reference resolves 3.22 mV per count, or 0.165 degrees, still fine. The sensor is therefore never the limiting factor on resolution; the limit is the accuracy of the reference and the offset of the converter input, and that is where a calibration step in production earns its keep.
The output driver matters at the sampling instant. The part is specified to hold 1000 pF of load with 500 microamps of drive, so a short trace into a sample and hold input is comfortable, while a long cable into a remote board is not. If the sensor sits on a probe lead, buffer it at the sensor end rather than adding capacitance at the converter end.
Supply, self heating and power cycling
Self heating is negligible in this body at these currents. At 5.5 V and 14.5 microamps the dissipation is 79.75 microwatts, and with 275 degrees per watt the die sits 0.022 degrees above the board around it. The figure only becomes relevant if the sensor is placed next to a regulator or on top of a power plane, and in that case the fix is placement, not compensation.
Power cycling works because the 800 microsecond turn-on is specified rather than typical only. In a battery node the sequence is: enable the sensor rail, wait 1 ms, sample the output, disable the rail. The supply current during the on time is 10 to 14.5 microamps, so a 1 percent duty cycle costs well under a microamp of average current, and the reading is available long before a digital sensor would have finished its first conversion.
The output is short circuit protected, which matters on a test fixture where a probe can slip onto the output pin while the board is powered. The specification allows the pin to be pulled to either rail within the absolute maximum window without damage, and the part recovers when the short is removed.
Reading the output on a mixed signal board
Three things decide whether the 0.5 degree typical accuracy survives to the converter. First, the ground of the sensor and the ground of the converter have to meet at one point, because the output is referenced to the local ground and a shared return carrying switching current shifts it. Second, the output trace should not run beside a switching node or an antenna feed, since the source impedance at the output is low but not zero and the 1000 pF load specification assumes a quiet node. Third, the supply should be bypassed at the pin with 0.1 microfarad, as the application section of the document recommends for the whole family.
For a board that also carries an RF front end, the sensor is usually placed on the opposite side of the shield from the power amplifier and read through the same ADC that monitors the PA bias. That arrangement is common in our telecom builds, and it works because the analog output has no clock and therefore no digital edge to couple into the receive chain.
When the reading is used for compensation rather than protection, the slope has to be corrected in firmware. The 19.5 mV per degree gain is specified with a tolerance, and the offset at 0 degrees is 400 mV nominal. A one point calibration at a known temperature removes the offset term; a two point calibration removes gain error as well. For a protection threshold the uncorrected part is adequate because the 2.5 degree maximum error is smaller than the margin normally left around a thermal trip point.
Where this sensor fits in a medical or telecom build
The TMP23x family lists grid infrastructure, wireless and telecom infrastructure, automotive infotainment, factory automation and test and measurement as target applications. In practice we see it in three places on customer boards: heatsink monitoring on a remote radio unit, board level ambient sensing inside a sealed enclosure where a digital bus would need an extra isolator, and battery or charger temperature sensing in a handheld instrument where the sensor has to keep working while the processor is in reset.
For medical instruments the analog output has a second advantage: it can be read by a separate safety monitor that shares no bus with the main processor, so a hung firmware image cannot hide an overtemperature condition. That separation is one of the arguments auditors accept when a device has a thermal hazard listed in its risk file. Our medical device component sourcing page collects the parts we keep for that class of build, and the sourcing route for the sensor itself is the same one we use for the rest of the BOM.
In telecom equipment the part is often chosen because it is footprint compatible with the LM20 and LMT8x parts that older boards used. That compatibility is stated in the feature list and is limited to the footprint, not the transfer function: the LM20 slope is different, so a board that swaps the part without a firmware change reads the wrong temperature. We flag that whenever a customer sends a cross reference request, and the pin to pin cross reference page describes how we check the electrical side before a substitution is approved.
Ordering, carrier and incoming checks
The orderable addendum prints TMP236A2DCKR as active, production, SC70 with 5 pins, 3000 pieces on a large reel, NIPDAU lead finish and moisture level 1 at 260 degrees. The sibling rows in the same table are worth reading before a purchase order is raised: the DCKT row is the small reel, the DBZR row is the SOT-23 body, and the A4 rows carry the looser grade. A purchase order that names only the family and the package can land on any of them.
Incoming inspection for this part is short. Check the reel label against the order code including the A2 grade, check the body marking against the addendum, measure the output at two known temperatures in a sample of five pieces, and confirm the moisture indicator. Because the part is level 1, no baking is needed before reflow, which removes one scheduling constraint from the assembly line.
If a customer needs the automotive grade of the same die, the -Q1 string is a different order code with its own qualification file, and mixing the two on one purchase order is a documentation error rather than a technical one. Our component traceability report service exists for the cases where a build has to prove which grade went onto which serial number.
Three questions buyers ask about this string
Is the DCK body available in the tighter grade? Yes, the addendum prints both A2 and A4 rows in the SC70 body, so the body choice does not force the grade. The string in this page is the A2 in SC70.
Can it replace a thermistor without a change to the divider? No. A thermistor divider is nonlinear and its output falls or rises with a curve, while this part is a straight line with a different span. The conversion in firmware changes, and the bias current through the divider disappears, which is usually the reason the change is made in the first place.
What happens below minus 10 degrees? The part continues to output a voltage proportional to temperature, but the accuracy is no longer specified. For a cold chain application the TMP235 member, specified from minus 40 degrees, is the correct choice, and the one stop BOM sourcing route can hold both strings on the same line so a single build can mix them where needed.