Contact Us

AMC22C11QDRQ1

Brand: Texas Instruments
Texas Instruments AMC22C11QDRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AMC22C11QDRQ1 — Power Management & Signal Chain | Superb Automation

AMC22C11QDRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The AMC22C11QDRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

AMC22C11QDRQ1: an isolated comparator that trips in 240 nanoseconds

AMC22C11QDRQ1 is an automotive isolated comparator with an adjustable threshold, an open drain output and a latch input. It is not a measurement device and it does not try to be one: it answers a yes or no question about whether a voltage crossed a limit, and it answers it in 240 nanoseconds typical while sitting across a galvanic barrier rated for 3000 VRMS.

That combination is what a traction inverter needs for overcurrent protection. The shunt sits on a phase node that swings with the switching, the controller sits on a low side ground, and the protection path cannot wait for a sampled measurement to come back through a serial bus. A comparator with its own barrier, its own high side supply and a hard wired output into the gate driver's fault pin is a shorter and more predictable path.

The device is AEC-Q100 grade 1, minus 40 to plus 125 ambient, in an 8 pin SOIC body on a 3000 piece reel. The figures below are from SBASAJ7B, revised December 2024, and from the orderable addendum. The document repeats one warning that is easy to miss and expensive to ignore, and it appears in the section on the threshold resistor.

The two hysteresis modes and the threshold window

The trip threshold is set by a single external resistor and the reference current that flows through it. The reference current is 100 microamps with a 1 percent tolerance, so the threshold is a linear function of one resistor value, and the trip threshold error is 1 percent maximum at 250 mV. That is a tighter specification than most comparator dividers achieve with two resistors and a reference.

The threshold range is split into two windows by the hysteresis mode. In low hysteresis mode the threshold spans 20 mV to 450 mV; in high hysteresis mode it spans 600 mV to 2.7 V. The gap between them is deliberate: a small threshold needs a small hysteresis to keep the trip point accurate, and a large threshold needs a large hysteresis to survive noise. There is no setting in the middle, and a circuit that needs a 500 mV threshold has to pick one side and accept the consequence.

The resistor value follows directly from the current source. A 250 mV threshold needs 2.5 kohm, a 20 mV threshold needs 200 ohm, and a 2.7 V threshold needs 27 kohm. The resistor tolerance adds directly to the threshold error, so a 1 percent resistor doubles the error budget that the part already spends. A 0.1 percent resistor costs a few cents and removes that term entirely.

Functionisolated comparator with adjustable threshold
High side supply3 V to 25 V
Low side supply2.7 V to 5.5 V
Threshold range, low hysteresis20 mV to 450 mV
Threshold range, high hysteresis600 mV to 2.7 V
Reference current100 microamps, 1 percent
Trip threshold error1 percent maximum at 250 mV
Propagation delay240 nanoseconds typical
Output typeopen drain, with optional latch mode
Latch behaviourcleared on the falling edge of the latch input
Transient immunity75 volts per nanosecond minimum
Isolation, VDE4250 VPK basic per DIN EN IEC 60747-17
Isolation, UL3000 VRMS for one minute per UL1577
Working voltage560 VRMS
PackageSOIC, D body, 8 pins, 4.9 mm by 6 mm
Carrier3000 pieces on a large reel
Marking22C11Q
Moisture levellevel 2 at 260 degrees, one year floor life
QualificationAEC-Q100 grade 1, minus 40 to plus 125

Basic isolation is the right rating for this job

The barrier is rated basic, not reinforced. That is a deliberate choice by the vendor and it fits the application: the comparator sits between a high side node and a low side controller inside the same enclosure, both of which are already isolated from the mains by the system barrier. A reinforced rating would be more expensive and would not be used.

The 560 VRMS working voltage is the number to check against the rail. A 400 V traction bus leaves margin, a 800 V bus does not, and an application that puts this part directly across an 800 V rail is outside the specified working voltage no matter what the qualification test says. Above that, the answer is a different family with a higher working voltage, not a different resistor.

The transient immunity of 75 volts per nanosecond is the parameter that decides whether the output chatters during a switching edge. A comparator with a slower front end will produce a burst of transitions every time the phase node moves, and the gate driver will treat that burst as a fault. The 75 V per nanosecond figure is measured in the same conditions the application presents, which is why it is printed as a minimum rather than as a typical.

Latch mode and the fault that stays latched

In transparent mode the output follows the input, so the fault signal disappears as soon as the current falls. In latch mode the output is cleared only on the falling edge of the latch input, and until then it stays asserted no matter what the current does. That distinction decides whether a short circuit produces a retry loop or a shutdown that a controller has to acknowledge.

For a traction inverter the latched behaviour is what the safety concept usually wants, because a fault that self clears can repeat at the switching rate and turn into a thermal event. For a charger the transparent behaviour is often preferred, because a transient overcurrent should not stop a charging session.

The latch input is on the low side and is referenced to the low side ground, so the controller drives it directly. It has an internal pull up in the direction that keeps the part in transparent mode if the pin is left open, which is the safe default for a board that has not yet decided.

Where the part sits in an electric vehicle

The document lists overcurrent and overvoltage detection in charging piles, onboard chargers, DC to DC converters and traction inverters. The four applications share a structure: a power stage, a shunt or a divider, a controller that must be protected, and a barrier between them.

The onboard charger is the neatest fit because the currents are lower and the switching frequency is higher. A comparator that trips in 240 nanoseconds can catch a short circuit before the inductor saturates, which is the difference between a fuse and a repair.

The charging pile is the other fit, and there the part usually monitors the output voltage rather than the current. A threshold set at 2.7 V with a 27 kohm resistor and a divider gives an overvoltage trip that is independent of the controller's own measurement chain, which is exactly the redundancy a safety reviewer asks for.

Our amplifier cross reference page covers the isolated signal chain parts we hold, and the component traceability report page describes the lot record we keep for automotive grade orders.

One last practical note on the resistor. The threshold resistor carries 100 microamps continuously, which is 2.5 microwatts at a 250 mV setting and 270 microwatts at 2.7 V. That is small enough that a 0402 body is adequate, and large enough that the resistor's temperature coefficient, not its tolerance, becomes the drift term at the top of the window.

Three questions buyers ask about this string

Can the threshold be changed at run time? Only by changing the resistor. There is no digital interface on this part, which is the point: a protection threshold that firmware can move is a threshold that firmware can get wrong.

Does the output need a pull up? Yes, it is open drain. The pull up goes to the low side rail and sets the rise time into the controller input.

Is the D package the same body as the analog isolators? Same SOIC 8 body outline, different internal barrier rating. Do not swap part numbers between families on the assumption that the footprint decides the safety rating.