STM32F100RBT6V
Product Specifications
STM32F100RBT6V
ST — MCU & Embedded Processors
Product Overview
The STM32F100RBT6V from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F100RBT6V: 128 Kbyte, LQFP64 body
STM32F100RBT6V is a member of the STM32F100 value line low and medium density described by DocID16455 Rev 9. The order code fixes 128 Kbytes of Flash, 8 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.
Order code and memory
| Order code | STM32F100RBT6V |
| Program Flash | 128 Kbytes |
| SRAM | 8 Kbytes |
| Package | LQFP64, 10 x 10 mm, 64 pins |
| Maximum general purpose I/O | 51 |
| Analog input channels | 16 of the 12 bit converter |
| Digital to analog converter | 2 channels of 12 bits |
| External memory controller | not present on this body |
| Supply voltage | 2.0 to 3.6 V |
| Maximum CPU clock | 24 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient, 105 C junction |
| Datasheet | DocID16455 Rev 9 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide |
| Clock sources | 8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal range 4 to 24 MHz |
| Timers | one advanced-control 16 bit timer with four channels and complementary outputs with dead time, up to six general-purpose 16 bit timers with four compare channels each, and two basic timers that trigger the converter |
| Serial interfaces | up to two SPI blocks, two I2C blocks and three USARTs, plus one HDMI CEC channel |
| DMA | 7 channel DMA controller |
| ADC | 12 bit successive approximation, 1 microsecond conversion, 10 channels on 48 pins and 16 channels on 64 and 100 pins |
| DAC | 2 channels of 12 bits with output buffers |
| Programmable voltage detector | eight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | VBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off |
| Flash endurance and retention | 10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C |
| Thermal resistance junction to ambient | 45 C/W on this package |
| Input tolerance | almost all inputs 5 V tolerant |
| USB | not present, USB full speed is the STM32F102 line |
| Status | production data per the datasheet cover |
Points to check before this part goes on a BOM
The V after the temperature digit is an internal code in the same way as the B on other codes of this line, so the figures that apply are the 128 Kbyte and 64 pin column of Table 2 in DocID16455 Rev 9: 8 Kbytes of SRAM, 51 general purpose I/O, 16 converter channels, the two 12 bit DAC channels and the full medium density interface set of two SPI blocks, two I2C blocks and three USARTs. A buyer matching only the family and the memory size can easily land on a different orderable string.
A board qualified on this code can normally be built from another revision of the same memory size, but the change is recorded work: a first article inspection, a converter check across all 16 channels and a current draw comparison at the same clock. What should not happen is two revisions on one assembly line under one part number, because a field return then cannot be traced to a single device revision and the failure analysis starts from an unknown.
The medium density peripheral set is the reason this memory size is popular in a 64 pin body: three USARTs, two SPI blocks, two I2C blocks, the CEC channel, one advanced-control timer, six general purpose timers and two basic timers. On a board that has a host link, a field bus, a display, a serial Flash and an EEPROM, all of those blocks have a use and none of them needs a second package.
The 8 Kbytes of SRAM is the working limit on this part. Three USARTs with 512 byte buffers is 1.5 Kbytes, the converter scan with double buffering and its descriptors is a few hundred bytes, and a control loop with fixed point maths and a look up table takes the rest. Firmware that needs a graphics buffer or a large protocol stack does not fit, and the neighbouring high density code with 24 Kbytes is the step that solves it rather than a memory size on the same line.
At 45 C/W the LQFP64 body allows about 440 mW between an 85 C ambient and the 105 C junction limit. The pins that carry the converter inputs and the DAC outputs sit on the analog side of the package, and the supply pins for the analog domain need their own capacitors. On a board with a switching regulator nearby, that separation is what keeps the last two bits of the converter usable rather than noise.
Flash endurance of 10 kcycles at minus 40 to plus 85 C with 30 years of retention at 85 C after one kcycle is the rating for the parameter store as well as for the code. A 128 Kbyte part is usually big enough for a bootloader and one application, so a field update rewrites the application area rather than swapping slots, which means one full erase and program cycle per update. Counting one update a quarter against the rating shows how much margin there is.
The internal RC oscillator at 1.1 percent at 25 C and 2.2 percent over the range is the fallback clock, and on a 64 pin board the two pins saved are often worth more than the accuracy. Where the application has to hold three serial links at high baud, or where the converter sample rate has to be accurate, the external oscillator accepts 4 to 24 MHz and the PLL takes it to the 24 MHz core clock.
Where this order code fits
It is the 128 Kbyte, 64 pin code with a trailing internal letter, used where a board was released on that revision and the same memory size from another revision is not an acceptable substitute without a deviation. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
What does the trailing V indicate? It is an internal code after the temperature digit, not a memory or package field. The memory, the package, the pin count and the peripheral set come from the 128 Kbyte, 64 pin column of Table 2 of DocID16455 Rev 9.
Is this part the same as STM32F100RBT6? The same memory size, package and peripheral set, as a different orderable string. Treating them as interchangeable is a substitution that should be recorded with a first article check rather than assumed from the datasheet figures.
Does it have an external memory bus? No. The value line low and medium density parts have no flexible static memory controller at any pin count. External storage on this board is a serial Flash or an EEPROM on the SPI or I2C blocks.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.