MAX9271GTJ+T
Product Specifications
MAX9271GTJ+T
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX9271GTJ+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
MAX9271GTJ+T: 1.5 Gbps Down One Coax Pair and a Status That Says Replace Me Later
The MAX9271GTJ+T is a 16-bit Gigabit Multimedia Serial Link serializer from Analog Devices in a 32-pin 5 mm by 5 mm TQFN with 0.5 mm lead pitch. It drives 50 ohm coax with FAKRA connectors or 100 ohm shielded twisted pair, pairs with the MAX9272 deserializer, and runs a serial bit rate to 1.5 Gbps from a 6.25 MHz to 100 MHz parallel clock. The parallel input can be single or double, and the double mode registers two pixels before serializing so the pixel clock can be twice as high. Core supply is 1.7 V to 1.9 V, the I/O supply is 1.7 V to 3.6 V, supply current is 75 mA maximum, and the part is specified from -40 C to +105 C. A control channel carries 9.6 kbps to 1 Mbps in UART and mixed modes and to 400 kbps in I2C mode, independent of video timing. There are five GPIOs and a GPO, programmable pre and de-emphasis for 15 m of cable, programmable spread spectrum, a PRBS generator for bit error rate testing, and error detection and correction coding. ESD is plus or minus 8 kV contact and plus or minus 15 kV air.
1.5 Gbps is 93.75 million sixteen-bit words a second
The line rate divided by the word width is 93.75 Mwords per second, and a 24-bit pixel needs one and a half words, so the payload ceiling is 62.5 Mpixel per second. A 1080p30 sensor at 24 bits per pixel asks for 62.2 Mpixel per second, which is 99.5 percent of that ceiling before the control channel, the error correction and the blanking overhead are counted. That is the number that decides whether one coax pair is enough: 1080p30 at 24 bits is at the edge, 1080p30 at 16 bits or 720p at 24 bits has room, and a 1080p60 sensor needs the double input mode or a second link. Quoting the 1.5 Gbps figure without the word width is where most of the optimism about this class of part comes from.
Fifteen metres of cable is about 75 ns of delay
Signal velocity in a foam dielectric coax is roughly 5 ns per metre, so 15 m is 75 ns, which is 112 bit periods at 1.5 Gbps. The video path does not care because the link is continuous, but the control channel and the frame sync do: a register read has to travel out and back, so the round trip is 150 ns plus the processing on both ends. Pre and de-emphasis is what allows the full 15 m at full speed, and the setting is a register value that has to be matched to the cable, not a fixed default. A shorter cable with the long cable setting wastes margin; a longer cable with the short setting closes the eye. The PRBS generator exists so this can be measured rather than guessed, and it is the check to run before a camera module is accepted.
The status word on this part is not a footnote
Analog Devices marks the MAX9271 as not recommended for new builds. The part is in production and buyable, so a line that already uses it can keep running, but a new camera platform that adopts it is adopting a part whose vendor has already pointed at its successor family. The successor parts are not drop-in: the pinout, the register set and the line rate all move, so a board change is required rather than a part change. For a buyer this changes the question from price to coverage: how much stock exists, what the second source looks like, and whether the module supplier has a migration path. A socket that can accept the older and the newer part is worth more than a discount on the older one.
| Parameter | Published value | What it decides |
|---|---|---|
| Serial bit rate | 1.5 Gbps | 93.75 M sixteen bit words per second |
| Payload at 24 bits | 62.5 Mpixel per second | 1080p30 is 62.2, so 0.5 percent of margin |
| Parallel clock | 6.25 MHz to 100 MHz | Double input doubles the pixel clock |
| Cable | 50 ohm coax or 100 ohm STP | Pre and de-emphasis buys 15 m |
| Control channel | 9.6 kbps to 1 Mbps, 400 kbps in I2C | Independent of video timing |
| Supply current | 75 mA maximum | 135 mW on the 1.8 V core |
| Supplies | 1.7 to 1.9 V core, 1.7 to 3.6 V I/O | 1.8 V and 3.3 V rails on one module |
| Temperature | -40 C to +105 C | Fits a camera housing, not a 125 C bay |
| Status | Not recommended for new builds | In production, but a migration question |
Is the deserializer a separate order code?
Yes. The serializer sits at the camera and the MAX9272 deserializer sits at the receiver, and both are ordered separately with their own temperature and package codes. A module quote that lists only one of the pair is incomplete, and the two ends have to be configured consistently: the same control channel mode, the same pre and de-emphasis pairing and the same spread spectrum setting. The pin and package comparison across this family is on the pin to pin cross reference, and the checks that catch a mismatch before a build starts are on the drop in replacement page. The complete category index is the analog and mixed-signal index.
What does the status mean for a line already running?
Nothing changes on the line, and the part stays available. What changes is the planning horizon: the last time buy and the migration cost belong in the same conversation as the unit price, because a camera module that cannot be reworked is a ten year commitment. The practical answer for an existing build is to hold stock against the annual volume and to qualify the successor on the next board revision rather than on an emergency basis.
Request Quote — In Stock, 100% New & Original, Full Warranty