Contact Us

MAX921CSA+T

Brand: Analog Devices
Analog Devices MAX921CSA+T is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MAX921CSA+T — Analog & Mixed-Signal ICs | Superb Automation

MAX921CSA+T

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The MAX921CSA+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

MAX921CSA+T: Four Microamps, a 1.182 V Reference and a Hysteresis Pin

The MAX921CSA+T is a single micropower comparator with an internal 1.182 V bandgap reference, a programmable hysteresis input, and a TTL and CMOS compatible output that can source 40 mA continuously. It draws less than 4 uA over the extended temperature range, runs from a single 2.5 V to 11 V supply or a plus or minus 1.25 V to plus or minus 5.5 V dual supply, accepts inputs from the negative rail to within 1.3 V of the positive rail, and propagates in 12 us at 10 mV of overdrive. The output stage draws no crowbar current when it switches, which removes the supply glitch that usually couples a comparator's transition into the rest of the board.

The part is the low power end of the comparator market: 4 uA is the current of a monitoring function that has to be alive for a decade, and the internal reference means the threshold does not need a second package.

Twelve microseconds against a 100 kHz period of ten

A propagation delay of 12 us is 120 percent of a 100 kHz period, so this comparator cannot follow a 100 kHz signal at all: the output arrives after the input has already changed again. It is a threshold detector for slow quantities, a battery voltage, a temperature, a door contact, and the 12 us figure should be read as the settling of a decision rather than as a signal path delay. The 10 mV overdrive in the specification is the other half: a 1 mV step is slower than 12 us, so a board that works on millivolts has to allow for more time.

The 1.182 V reference is plus or minus 1 percent, which is 11.8 mV, and that uncertainty appears at the comparator input directly. A divider that sets a 3.0 V trip point with a ratio of 0.394 turns the 11.8 mV into 30 mV at the rail, which is 1 percent of the threshold. That is good enough for a low battery warning and marginal for a protection cutoff, where the divider tolerance usually dominates anyway.

Reference1.182 V, plus or minus 1 percent, 11.8 mV
Supply currentUnder 4 uA, 20 uW at 5 V, 35 mAh over a year
Supply range2.5 V to 11 V single, plus or minus 1.25 V to plus or minus 5.5 V dual
Input rangeNegative rail to 1.3 V below the positive rail, so 3.7 V on a 5 V supply
Propagation12 us at 10 mV of overdrive, 120 percent of a 100 kHz period
OutputTTL and CMOS compatible, 40 mA continuous source, no crowbar current
HysteresisSet by two resistors on the HYST pin, no feedback calculation
Package8-lead SO, the smallest in this family

Forty milliamps of source current is unusual for a micropower part

Most comparators in this current class have an open drain output that sinks a few milliamps and needs a pull up. This one sources 40 mA continuously, which is enough to drive a small relay coil, an LED, or a logic input with a heavy capacitive load. Into 100 ohm that is 4 V, which is the full swing of a 5 V rail; into 1 kOhm the same 40 mA would need 40 V and the output simply saturates at the rail, so the figure describes a current capability rather than a voltage.

The 4 uA maximum belongs to the single MAX921 and the dual MAX923. The quad member of the family does not carry the same figure, and a board that budgets 4 uA for four comparators is out by the number of amplifiers. That kind of family level number is the most common purchasing error in this class, because the summary table quotes the best member.

Two questions buyers ask

How is the hysteresis set?
Two resistors on the HYST pin, which is the point of the part: the internal circuit injects a current into the reference divider so the trip point moves after a transition, and the two resistors scale that movement. No positive feedback around the input is needed, so the input impedance does not change with the hysteresis setting and the calculation is a resistor ratio rather than a loop equation. The data sheet gives the ratio for a given hysteresis.

Can it monitor a negative rail?
The input range includes the negative supply, so a signal that sits below ground can be compared as long as the part is powered from a supply that includes it. On a dual supply the inputs work from the negative rail up to 1.3 V below the positive rail, which covers a plus or minus 5 V system with the usual headroom at the top.

Ordering and supply

The CSA suffix is the 8-lead SO package in tape and reel. Substitution traps are the current for the specific member, the input range at the positive rail and the output type: an open drain part needs a pull up and cannot source, and a part whose input stops at the positive rail minus 2 V will not see a signal that reaches close to the rail.

We hold and source this family for production and repair lots. Start from the analog mixed signal ICs family page, compare a candidate against the amplifier cross reference, and where a comparator has to be changed on a board that is already built, the steps in how to verify a drop in replacement put the threshold and the output type ahead of the timing.

Request Quote — In Stock, 100% New & Original, Full Warranty