Contact Us

MAX706TESA+T

Brand: Analog Devices
Analog Devices MAX706TESA+T is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MAX706TESA+T — Analog & Mixed-Signal ICs | Superb Automation

MAX706TESA+T

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The MAX706TESA+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

MAX706TESA+T: A 4.40 V Threshold, a 1.6 Second Watchdog and a 1.25 V Power-Fail Input

The MAX706TESA+T is the 4.40 V member of the MAX705 to MAX708 supervisory family in an 8-lead SO package. It provides a reset output during power up, power down and brownout with a 200 ms pulse, an independent watchdog output that goes low if the watchdog input has not been toggled within 1.6 s, a 1.25 V threshold comparator for power fail or low battery warning, and an active low manual reset input. The MAX705, MAX707 and MAX813L use a 4.65 V threshold instead, and the MAX707, MAX708 and MAX813L substitute an active high reset for the watchdog.

Four functions in eight pins is why this family outlived most of its competitors: a processor on a 5 V rail needs a brownout reset, a watchdog and a warning before the rail collapses, and the 1.25 V comparator covers the last of those with two resistors.

Four point four volts is twelve percent below a 5 V rail

A 5 V rail at minus 5 percent is 4.75 V, which is 350 mV above the 4.40 V threshold, and at minus 10 percent it is 4.50 V, which is still 100 mV above. The part therefore does not trip on a legal 5 V rail even at minus 10 percent, and it trips at 12 percent below nominal. That is the right behaviour for a 5 V logic rail, where the processors of that generation were specified to 4.75 V and could survive a short excursion below it. The MAX705 at 4.65 V leaves only 100 mV at minus 5 percent, so the choice between the two members is a decision about how much supply tolerance the board expects.

The 1.25 V power fail comparator is a separate input and it is the one that is usually set up wrong. To warn at 4.5 V the divider ratio has to be 1.25 divided by 4.5, which is 0.2778: a 100 kOhm upper resistor and a 38.3 kOhm lower resistor give 0.277 and a trip at 4.51 V. The current through that divider is 4.5 V across 138.3 kOhm, or 32.5 uA, which is small but not zero, and it runs continuously from the rail the part is monitoring.

Threshold4.40 V, which is 12 percent below a 5 V nominal
Margin350 mV on a 5 V rail at minus 5 percent, 100 mV at minus 10 percent
Reset pulse200 ms, active low output plus active low manual reset input
Watchdog1.6 s timeout, independent output
Power fail input1.25 V threshold, 0.2778 divider ratio for a 4.5 V warning
Divider example100 kOhm and 38.3 kOhm, 32.5 uA of continuous divider current
Family4.65 V in the MAX705, MAX707 and MAX813L, 4.40 V in the MAX706 and MAX708
Package8-lead SO, also DIP and microMAX in the family

The watchdog output is not a reset until it is wired to one

The watchdog output goes low when the timeout expires, and on this part it is a separate pin. To turn a hung processor into a reset, that pin has to be connected to the manual reset input, which is the same arrangement as the MAX823 family. A board that leaves it open has a supervisor that reports the hang on a pin nobody reads, and the failure only shows up in the field when a processor locks up and stays locked up until the power is cycled.

The 200 ms reset pulse is longer than the MAX811 family's 140 ms and suits processors that need a longer reset for their internal regulator to settle. It is also shorter than the 1.6 s watchdog, so a reset event does not itself trigger the watchdog, which would otherwise produce a reset loop on a board where the two pins are tied together.

Two questions buyers ask

What is the difference between the MAX705 and the MAX706?
The threshold: 4.65 V against 4.40 V, and nothing else. The MAX707 and MAX708 are the same two thresholds with an active high reset and no watchdog, and the MAX813L is the 4.65 V part with an active high reset. Because the difference is a single digit in the order code and the package and pinout are identical, a mis picked reel produces a board that either resets early or never resets at all.

Can the power fail comparator monitor a different rail?
Yes, that is its purpose. The 1.25 V threshold compares an external divider against an internal reference, so it can watch a 12 V rail, a battery, or an unregulated input while the reset function watches the 5 V rail. The divider has to be calculated for the warning point, and the tolerance of the two resistors adds directly to the tolerance of the 1.25 V reference.

Ordering and supply

The ESA suffix is the 8-lead SO package in tape and reel. Substitution traps are the threshold, the reset polarity and the watchdog: a MAX707 in a MAX706 socket has an active high reset and no watchdog, so the processor is held in reset and the hang detection is gone. Any candidate also has to be checked for the 200 ms pulse, because a part with a 140 ms pulse is a different reset requirement.

We hold and source this family for production and for repair lots. Start from the analog mixed signal ICs family page, compare a candidate against the power management cross reference, and where a supervisor has to be replaced on a built board, the order in how to verify a drop in replacement puts the threshold and the reset polarity first.

Request Quote — In Stock, 100% New & Original, Full Warranty