Contact Us

MAX9813HEKA+T

Brand: Analog Devices
Analog Devices MAX9813HEKA+T is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MAX9813HEKA+T — Analog & Mixed-Signal ICs | Superb Automation

MAX9813HEKA+T

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The MAX9813HEKA+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

MAX9813HEKA+T: Two Microphones Into One 20 dB Stage on 230 Microamps

The MAX9813HEKA+T is a dual-input microphone amplifier from Analog Devices in an 8-pin SOT23 measuring 3 mm by 3 mm. Gain is fixed at 20 dB, the output swings rail to rail, bandwidth is 500 kHz, total harmonic distortion plus noise is 0.015 percent, and power supply rejection is 100 dB at 217 Hz. Supply current is 230 microamps and shutdown current is 100 nanoamps, which cuts the amplifier and its bias generator together. The H grade runs from 4.5 V to 5.5 V and generates a 4.0 V microphone bias internally; the L grade runs from 2.7 V to 3.6 V with a 2.3 V bias. The two inputs let two microphones share one output, so the second capsule costs one pin rather than a second amplifier, and the part is specified from -40 C to +85 C.

20 dB is 10 times, and that fixes the whole level plan

A fixed 20 dB means the output is ten times the input, so a microphone delivering 10 mV RMS produces 100 mV RMS at the output and a 100 mV capsule produces 1 V. There is no gain resistor and nothing to trim, which is the point: the level plan is set by the capsule sensitivity and the converter's full scale, and the amplifier is a constant in it. On a 5 V supply with a rail-to-rail output the ceiling is about 5 V peak to peak, or 1.77 V RMS, so a capsule at 100 mV RMS reaches 1 V RMS and leaves 5 dB of headroom before clipping. A capsule at 200 mV RMS leaves no headroom at all, and the fix is a different capsule rather than a different amplifier. This is the calculation to run before choosing between the fixed gain part and an automatic gain control part.

The 100 dB rejection figure holds at 217 Hz

One hundred decibels of rejection is 10 microvolts of output per volt of supply ripple at that frequency, which is the number that matters when the rail is a switching converter at a few hundred kilohertz and the audio band is below 20 kHz. At 217 Hz the rejection is quoted; above the audio band it falls, and a 1 MHz switcher is not covered by the figure. In a product with a 2 MHz converter the practical answer is a small series resistor and a capacitor on the supply pin, and the 230 microamp supply current is what allows a 100 ohm series resistor to drop only 23 mV. That resistor and capacitor are the difference between a specification and a working board.

Two inputs, one output, and a bias that has to survive the switch

The two inputs are summed or selected externally, and each capsule needs its own bias resistor from the internal 4.0 V supply. At a typical 250 microamp capsule current a 2.2 kilohm resistor drops 0.55 V and leaves 3.45 V across the capsule, which is inside the range electret capsules expect. Because the bias is shared, switching between two capsules with very different current draw moves the bias node, and a 100 microfarad or larger capacitor at the bias pin is what keeps that step out of the audio path. The bias generator is inside the part, so the external bill of materials is two resistors and two capacitors per channel rather than a separate low noise reference.

ParameterPublished valueWhat it decides
Gain20 dB fixed10 times, no external setting
InputsTwo, one outputSecond capsule costs one pin
Supply, H grade4.5 V to 5.5 VBias 4.0 V, so a 5 V rail
Supply, L grade2.7 V to 3.6 VBias 2.3 V, so a 3.3 V rail
Supply current230 uA1.15 mW at 5 V, 2.0 Ah over a year
Shutdown current100 nA0.9 mAh over a year
Rejection100 dB at 217 Hz10 uV of output per volt of ripple
Distortion plus noise0.015 percentMinus 76.5 dB
Bandwidth500 kHzFar above the audio band
Package8-pin SOT23, 3 by 3 mmFits beside the capsule

Does 230 microamps matter in a battery product?

Over a year it is 2.0 Ah, which is larger than many single-cell products carry in total. That is not a criticism of the part, since it is among the lower figures in its class, but it does mean the shutdown mode is the operating mode: 100 nanoamps for a year is 0.9 mAh, so a product that keeps the amplifier enabled continuously is spending its budget on a microphone that is not being listened to. The enable pin belongs under the same control as the audio path, and the settling time after enable is the number to check against the time the processor needs before it starts sampling.

Why is the H version not a substitute for the L version?

They are the same amplifier on different supplies: H runs 4.5 V to 5.5 V with a 4.0 V bias, L runs 2.7 V to 3.6 V with a 2.3 V bias. Putting an H part on a 3.3 V rail is outside its supply range, and putting an L part on 5 V exceeds its maximum. The bias voltage also differs, so the capsule sees a different operating point and the sensitivity changes. A reel substitution between the two grades changes both the power supply requirement and the acoustic gain, which is why the grade letter belongs on the assembly drawing. The amplifier range is on the amplifier cross reference, the patient monitoring and diagnostic audio cases are on the medical device components page, and the full category is the analog and mixed-signal index.

Request Quote — In Stock, 100% New & Original, Full Warranty