Contact Us

STM32F100C6T6B

Brand: ST
ST STM32F100C6T6B is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F100C6T6B — MCU & Embedded Processors | Superb Automation

STM32F100C6T6B

ST — MCU & Embedded Processors

Product Overview

The STM32F100C6T6B from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F100C6T6B: 32 Kbyte, LQFP48 body

STM32F100C6T6B is a member of the STM32F100 value line low and medium density described by DocID16455 Rev 9. The order code fixes 32 Kbytes of Flash, 4 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F100C6T6B
Program Flash32 Kbytes
SRAM4 Kbytes
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels10 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllernot present on this body
Supply voltage2.0 to 3.6 V
Maximum CPU clock24 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDocID16455 Rev 9

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Clock sources8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal range 4 to 24 MHz
Timersone advanced-control 16 bit timer with four channels and complementary outputs with dead time, up to six general-purpose 16 bit timers with four compare channels each, and two basic timers that trigger the converter
Serial interfacesup to two SPI blocks, two I2C blocks and three USARTs, plus one HDMI CEC channel
DMA7 channel DMA controller
ADC12 bit successive approximation, 1 microsecond conversion, 10 channels on 48 pins and 16 channels on 64 and 100 pins
DAC2 channels of 12 bits with output buffers
Programmable voltage detectoreight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainVBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off
Flash endurance and retention10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C
Thermal resistance junction to ambient55 C/W on this package
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

The order code reads through the scheme: C is the 48 pin LQFP at 7 x 7 mm, 6 is 32 Kbytes of Flash, T is the LQFP body and the first 6 is the industrial range of minus 40 to plus 85 C ambient. The trailing B is an internal code rather than a memory or package field, so the 32 Kbyte column of Table 2 and the 37 general purpose I/O figure are the ones that apply. A qualification report should carry the exact orderable string, because the same document, DocID16455 Rev 9, covers every code in the line and only the string tells a tester which one was on the bench.

The 4 Kbytes of SRAM is the real limit on this part, not the 32 Kbytes of Flash. A Cortex-M3 frame plus an interrupt stack plus a receive buffer for the three USARTs and the two I2C blocks is already a kilobyte before the application starts, and the 7 channel DMA controller needs a descriptor and a buffer for each stream it serves. Firmware that keeps a 1 Kbyte calibration table in RAM and also runs a protocol stack copes; firmware that buffers a whole protocol frame of 512 bytes twice does not.

Every function on a 48 pin body costs pins. The 10 converter channels are shared with port A, port B and port C, the crystal takes two pins when an external resonator is fitted, and the debug port takes two for serial wire and five for JTAG. A board with a crystal, serial wire debug and all 10 analog inputs therefore has about 30 I/O left for the application, which is the number to start from when the connector assignment is being written rather than the headline 37.

The LQFP48 body is rated 55 C/W junction to ambient, so the 20 C the grade allows between 85 C ambient and 105 C junction works out at about 360 mW of total dissipation. That budget covers the core, the two converters when they run and every output pin that sinks current. A board driving ten LEDs at 8 mA each spends 264 mW of the 360 mW before the core draws anything, which is why the I/O current is worth adding up on a part this small.

The programmable voltage detector has eight falling thresholds between 2.00 V and 2.88 V nominal, each with a rising edge about 100 mV higher. Against a 3.3 V rail at minus five percent, which is 3.135 V, even the highest threshold sits 255 mV below the rail, so the warning is a genuine margin rather than a trip on a legal supply. Against a 3.0 V rail the top threshold leaves 120 mV, and that difference decides which level the firmware should select.

The HDMI CEC channel is a single wire interface with its own clock generation and its own address scheme, which is what makes it useful on a set top box or a display controller and useless as a spare UART. It also has to be pulled to the right level on the connector side, and the pin it uses is one of the 37, so a board that does not need remote wake is better off treating that pin as general purpose I/O from the start.

Where this order code fits

It is the 32 Kbyte, 48 pin member of the value line, used on appliance control boards, small motor drives and sensor nodes that want 32 bit math and a 12 bit converter inside a 7 x 7 mm body. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Does the trailing B in STM32F100C6T6B change the memory or the pin count? No. The B is an internal code after the temperature digit. The memory, the package and the pin count are the ones in the C6 row of Table 2 of DocID16455 Rev 9, which is 32 Kbytes of Flash, 4 Kbytes of SRAM and the 48 pin LQFP. Order the exact string and keep it on the drawing, because a substitute with a different trailing letter is a different orderable part even when the figures match.

Can this part be used for a USB interface? No. The STM32F101 and STM32F100 lines carry no USB peripheral at any density. USB full speed is the STM32F102 line, which has the same pin out on 48 and 64 pins, or the STM32F103 line where the converter and timer count are also higher. A board that needs USB and has already placed this part needs a different pin out, not a firmware change.

Is 32 Kbytes and 4 Kbytes enough for a bootloader plus an application? It depends on what the application buffers. A bootloader of 6 to 8 Kbytes leaves 24 Kbytes of Flash, which is comfortable for a control loop and a protocol stack, while the 4 Kbytes of SRAM is the tighter number because the stack, the DMA buffers and the calibration table all live there. Parts that need two application images, for example an A and a B slot for field updates, are outside this memory size.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.