HXC50143
Product Specifications
HXC50143
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC50143 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC50143: one part number, two LDMOS rows, 100 W at 28 V and 30 W at 12.5 V
HXC50143 is a laterally diffused MOS power transistor from Hisiwell that appears twice in the vendor LDMOS table. The first row prints VHF to 1.5 GHz, 100 W, 18 dB of gain, 65 percent drain efficiency and a 28 V rail in continuous wave. The second row prints HF to 1 GHz, 30 W, 17 dB of gain, 65 percent efficiency and a 12.5 V rail in continuous wave. Same part number, two power classes, two rail voltages, and a band description that starts at HF in one row and VHF in the other. That duplication is not a typo in this page, it is what the vendor table shows, and it is the single most important fact a buyer of this number has to settle before the order goes out.
LDMOS is the technology choice that sits below GaN in frequency and usually below it in cost. At 1 GHz and under, an LDMOS die has enough gain, a ruggedness that survives a bad load for a long time, and a price per watt that GaN does not match. That is why the VHF and UHF broadcast bands, the industrial 13.56 MHz and 27 MHz bands and a large part of the tactical radio market are still LDMOS. The 28 V row of this part is the one that fits a modern 28 V transmitter; the 12.5 V row is the one that fits a legacy 12 V mobile architecture where the battery rail is the drain rail.
The figures come from the Hisiwell LDMOS category table read on 4 November 2026, plus the arithmetic that follows from them. The table prints band, output power, gain, efficiency, rail and mode, and both rows of this number are complete, which is not true of every row in the same table. Where a number is not printed this page says so.
Telling the two rows apart before a purchase order
The rail is the discriminator. 100 W on 28 V draws 5.5 A at 65 percent efficiency, while 30 W on 12.5 V draws 3.7 A. A board built for one row will not work with the other: the matching network is set for a different load line, the bias network is set for a different gate voltage window, and the decoupling is sized for a different current. A quote that does not state which row it prices is a quote that has not been checked.
The band description is the second clue. The 100 W row is described as VHF to 1.5 GHz, which takes in the FM broadcast band at 87.5 MHz to 108 MHz, the VHF television band and the 1.2 GHz to 1.4 GHz aeronautical and industrial allocations. The 30 W row is described as HF to 1 GHz, which starts at 3 MHz and covers the HF broadcast and the 27 MHz industrial band as well as the low VHF. In practice the die is the same family and the difference is the package and the matching, so the band description is a statement about what the vendor has characterised rather than a hard limit of the silicon.
The third clue is the gain. 18 dB against 17 dB at the same efficiency is a small difference that points to a different internal matching and a different package. It also matters for the driver stage: one decibel of gain at this power level is a driver that has to be a class higher.
The LDMOS ladder around this number
| Part number | Band | Output | Gain | Efficiency | Rail | Mode |
| HXC50205 | VHF to 1 GHz | 300 W | 19 dB | 70 percent | 28 V | CW |
| HXC50204 | VHF to 1 GHz | 100 times 2 W | 15 dB | 65 percent | 28 V | CW |
| HXC50143 | VHF to 1.5 GHz | 100 W | 18 dB | 65 percent | 28 V | CW |
| HXC50143 | HF to 1 GHz | 30 W | 17 dB | 65 percent | 12.5 V | CW |
| HXC50142 | HF to 1 GHz | 20 W | 15 dB | 65 percent | 12.5 V | CW |
| HXC50176 | HF to 0.5 GHz | 150 times 2 W | 18 dB | 65 percent | 28 V | CW |
| HXC50169 | HF to 1 GHz | 70 times 2 W | 18 dB | 60 percent | 28 V | CW |
| HXC50175 | HF to 1 GHz | 115 times 2 W | 15 dB | 65 percent | 28 V | CW |
| HXC50156 | HF to 1.5 GHz | 40 W | 20 dB | 60 percent | 28 V | CW |
| HXC50155 | HF to 1.5 GHz | 25 W | 20 dB | 60 percent | 28 V | CW |
| HXC50153 | HF to 2 GHz | 10 W | 23 dB | 63 percent | 28 V | CW |
Reading the ladder gives three usable rules. Gain falls as output power rises, from 23 dB at 10 W to 15 dB at 100 times 2 W, so a high power stage needs more driver stages. Efficiency is flat at 60 to 65 percent across a whole family, which tells you the vendor is quoting a mature process rather than a laboratory result. And the dual rows sit at the same power as the single rows above them, which is why the part number has to be checked for the times two notation before the combiner is specified.
The numbers for both rows of this part
| Function | LDMOS RF power transistor, flange mount |
| Row one band | VHF to 1.5 GHz |
| Row one output | 100 W, which is 50 dBm |
| Row one gain | 18 dB |
| Row one efficiency | 65 percent |
| Row one rail | 28 V, which is 5.5 A at 65 percent efficiency |
| Row two band | HF to 1 GHz |
| Row two output | 30 W, which is 44.77 dBm |
| Row two gain | 17 dB |
| Row two efficiency | 65 percent |
| Row two rail | 12.5 V, which is 3.7 A at 65 percent efficiency |
| Operating mode, both rows | Continuous wave |
| Heat, row one | 53.8 W continuous |
| Heat, row two | 16.2 W continuous |
| Technology | Laterally diffused MOS on a silicon substrate |
| Matching | Input and output matched on the package for the stated band |
| Package | Flange mount, screw down |
| Thermal resistance | In the device document, not in the category table |
Why LDMOS still wins at this band
Three properties decide it. Ruggedness: an LDMOS die survives a load mismatch that would take a GaN device out, which matters on a broadcast transmitter whose antenna can ice up or be disconnected during maintenance. Cost per watt at 1 GHz and below: the process is mature and the die area per watt is smaller than it was, so the price is the lowest of the three technologies at this band. And a lower rail for the small power classes: the 12.5 V row exists because a 12 V architecture is still common in mobile and transportable equipment.
The trade is power density. At 1.5 GHz an LDMOS die needs more area than a GaN die for the same output, which is why the 300 W row exists at 28 V and why the ladder stops at 1.5 GHz. Above that band the vendor's own range switches to GaN, and a requirement that needs 100 W at 3 GHz is not an LDMOS requirement at all.
The bias is the part of an LDMOS stage that gets the least attention and causes the most field failures. The gate threshold drifts with temperature, so a fixed gate voltage gives a drain current that climbs as the flange heats. A bias network with temperature compensation, or a controller that closes the loop on drain current, is what keeps the part inside its safe area over a long transmission.
What to settle before this number is quoted
Four items: which row, which band, which package, and which test paperwork. The first is the one that matters most, because the same number is listed at 100 W on 28 V and 30 W on 12.5 V, and a purchase order that does not carry the rail will be filled against whichever row the supplier has in stock. We ask for the rail and the band on every enquiry for this number, and we state both on the quote.
The second item is the band edge. A part characterised to 1.5 GHz used at 1.6 GHz is outside the vendor characterisation, and the gain and efficiency in the table no longer describe it. The third is the package and the flange, because a part that is right electrically and wrong mechanically is a scrap part. The fourth is the paperwork the programme needs, a certificate of conformance at the least, a date code report and a traceability record if the end equipment is going into a regulated market.
Related pages: RF power transistor cross reference for the alternative rows at this band, how to choose an RF amplifier for the stage budget around the device, RF and microwave board support for the laminate and the flange assembly, and RF procurement for the supply route.
Questions buyers ask about this LDMOS number
Are the two rows the same die. The vendor table does not say, and this page does not invent an answer. What the two rows do say is that the characterised output, gain and rail differ, which is enough to know that a board cannot be moved from one row to the other without a new matching network and a new bias setting.
Can a 30 W 12.5 V part be run at 28 V for more output. No. The drain voltage is a rating, not a suggestion, and a part characterised at 12.5 V run at 28 V is outside its characterisation and outside its safe area. The 28 V row is the answer for a 28 V board.
What does 65 percent efficiency mean in a real transmitter. It means 53.8 W of heat for a 100 W output, which is a heatsink of roughly 0.5 degrees per watt to hold a 40 degree rise. That is a copper block, not an extruded profile, and the flange flatness matters more than the heatsink mass.