Contact Us

VBGQT1801

Brand: VBsemi
VBsemi VBGQT1801 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGQT1801 — Discrete & Power Semiconductors | Superb Automation

VBGQT1801

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGQT1801 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGQT1801: 80 V and 350 A in a TOLL body

The VBGQT1801 is a single N channel MOSFET rated at 80 V drain to source with a plus or minus 20 V gate window and a threshold of 3.5 V. It carries 350 A and its on resistance is 1 milliohm at a 10 V gate. The silicon is a shielded gate structure and the body is TOLL, the surface mount package with a large clip bonded tab that the industry uses for high current switches.

One milliohm at 80 V is the top of what a single die does in this voltage class. At 100 A the part drops 100 millivolt and dissipates 10 watt, which a TOLL tab on a decent copper area handles. At 200 A it dissipates 40 watt, which needs a heatsink or a cold plate. The 350 A figure is a pulse and die limit.

The 80 V rating sits between the 60 V class that covers a 48 V rail and the 100 V class that covers a 72 V pack. For a 48 V system with a modest overshoot, 80 V is the balanced choice: more margin than 60 V, less resistance than 100 V.

Key data for the VBGQT1801

ConfigurationSingle N channel
PackageTOLL, surface mount with clip bonded tab
VDS80 V
VGSPlus or minus 20 V
Vth3.5 V typical
ID350 A, a die limit at a 25 C case
RDS(on) at 10 V1 milliohm
TechnologyShielded gate trench
Gate chargeNot published on the catalogue page, and at this die size the driver has to be sized from the data sheet
Body diodeIntrinsic, with a recovery that matters in a bridge at this current
TabClip bonded, which is what allows the current density in a surface mount body
MountingReflow only, with the tab soldered to a large copper area and a thermal plane below

The gate is the constraint, not the channel

With 1 milliohm of channel resistance the conduction loss at 100 A is 10 watt, and the switching loss at 100 kHz with a large gate charge can be of the same order. That balance is the whole engineering problem for a part in this class: the die is so large that the gate charge is measured in hundreds of nanocoulombs, and the driver has to deliver that charge in a short enough time to keep the switching interval small.

A driver with 4 A of peak current charges 200 nC in 50 ns, which at 80 V and 100 A is a switching loss of about 0.4 millijoule per transition, or 40 watt at 100 kHz for both edges. That is four times the conduction loss and it is the reason high current stages run at lower frequency or use soft switching.

The threshold of 3.5 V is high, which helps with false turn on at a fast switch node but means the gate has to be driven to 10 V to reach the published resistance. A 5 V drive would sit only 1.5 V above threshold and produce a resistance several times the headline.

TOLL and what a clip bonded tab changes

The TOLL body replaces the bond wires with a copper clip from the die to the tab. That removes the wire resistance and, more importantly, the wire inductance, which is what limits the current in a fast switching loop. A clip bonded part can switch faster and carry more current in the same footprint than a wire bonded body of the same die area.

The trade is mechanical. The tab is large and it has to be soldered flat, so the copper island under it needs to be solid, not a set of thin traces. Voids under a tab of this size become hot spots, and a hot spot on a 1 milliohm die at 100 A is where the part fails.

Reflow profile also matters more than usual. A large tab takes longer to reach reflow temperature and it cools more slowly, so the soak and the ramp are set by the biggest thermal mass on the board, which is this part. A board with several of these needs a profile built around them rather than around the small parts.

Supplying a 1 milliohm switch

Parts in this cell are made by a small number of vendors, and the second source question is usually about the tab and the gate charge rather than the resistance. A candidate with the same 1 milliohm and a different tab geometry is not a drop in even if the pinout matches, because the solder joint and the thermal path are part of the specification. Our safety stock planning page covers how a programme holds a buffer on a part whose second source is not a true equivalent.

For a production line the practical issue is often the reflow profile and the void rate under the tab rather than the electrical performance. That is a process question, and it is answered by an X-ray of the first articles rather than by a datasheet.

The sourcing side of this part is covered on the supplier quality audit. For a part whose tab and reflow profile decide the yield, that page covers what is asked of a source before it is approved.

Questions we get on this code

Is 350 A a continuous rating? No. Continuous current is set by the tab and the copper. At 100 A the part dissipates 10 watt, and that is already a heatsink sized load in most products.

Can it be hand soldered for a prototype? Not reliably. The tab is large and a hand joint leaves voids. Prototypes normally use a reflow process or a socketed test fixture.

Is a 5 V gate drive enough? No. The 1 milliohm figure is at 10 V and the threshold is 3.5 V, so a 5 V drive leaves 1.5 V of overdrive and a resistance well above the headline.

What is the packing? TOLL parts normally ship on a large reel in the low thousands. We confirm the reel size and the taping orientation on the quotation.