Contact Us

VBFB1606

Brand: VBsemi
VBsemi VBFB1606 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBFB1606 — Discrete & Power Semiconductors | Superb Automation

VBFB1606

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBFB1606 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBFB1606: 60 V and 97 A in a TO251

The VBFB1606 is a single N channel MOSFET rated at 60 V drain to source, with a plus or minus 20 V gate window and a threshold of 2.5 V. It carries 97 A and its on resistance is 6 milliohm at a 4.5 V gate and 5 milliohm at 10 V, on trench silicon in the TO251 body, which is the three lead through hole package also sold as the intermediate power package.

A 60 V, 5 milliohm die at 97 A is a power tool part, a brushless motor part, or the low side of a 48 V converter. The numbers only make sense together: 6 milliohm at 20 A is 2.4 watt, which is a real heat load that the tab has to carry, and 97 A is what the die can pass for a short pulse with the case held at 25 C.

The threshold of 2.5 V is the one number that says this is not a logic level part in the modern sense. It will turn on from a 5 V gate, and it will be usable at 4.5 V, but a 3.3 V drive sits only 0.8 V above threshold, which is a region where the resistance is several times the published figure.

Key data for the VBFB1606

ConfigurationSingle N channel
PackageTO251, three lead through hole with tab
VDS60 V
VGSPlus or minus 20 V
Vth2.5 V typical
ID97 A, a package claim at a 25 C case
RDS(on) at 4.5 V6 milliohm
RDS(on) at 10 V5 milliohm
TechnologyTrench
Gate chargeNot published on the catalogue page
Body diodeIntrinsic, and in a motor bridge it carries the freewheel current
MountingTab bolted or clipped to a heatsink, or soldered to a copper island on the board

97 A is a pulse number and 20 A is a working number

The way to read a 97 A rating on a 5 milliohm die is to work backwards from the heat. At 97 A the conduction loss would be 47 watt, which no TO251 can shed without a heatsink and a fan. At 20 A the loss is 2 watt, which a tab on a modest copper island handles with the junction 40 to 50 degrees above ambient. At 10 A it is 0.6 watt and the package is not the constraint at all.

So the rating is real in the sense that the die survives it for the duration the vendor specifies, and irrelevant in the sense that the thermal path limits continuous current long before the current limit does. Any quotation or datasheet discussion that quotes 97 A without the case temperature and the pulse width is quoting a marketing figure.

The gate charge matters as much as the resistance here. A 5 milliohm die is a large die, and a large die has a large gate. Driving it at 20 kHz from a weak pin produces slow transitions, and slow transitions in a motor bridge are where the switching loss and the shoot through current come from. A dedicated driver with a peak current in the amp range is the normal pairing.

The TO251 tab and what it demands of the board

The TO251 is the smaller sibling of the TO220 with the same 2.3 mm lead spacing and a narrower tab. It mounts vertically and it can be screwed to a heatsink, clipped to one, or soldered down to a copper island as a surface part. Each of those routes gives a different thermal resistance, and the difference between them is larger than the difference between this part and a competitor with the same die.

For a hand soldered prototype the tab is usually bolted with a thermal pad and no insulating washer, which means the drain is at the heatsink potential. That is fine when the heatsink is isolated and it is a fault path when it is not. For a production board the tab is normally soldered to a copper island with vias to an inner layer, and then the copper area is the rating.

The three leads are thick and the through holes are large, which is good for current and awkward for a reflow process. Most boards that use this body are wave soldered or selectively soldered on the power side, and that is a process decision that has to be made before the board is released, not after.

Second sourcing a 60 V power part

The cells in this class, 60 V and 4 to 8 milliohm in a TO251 or TO220, are occupied by most of the large vendors, and the differences between them are usually in gate charge and in the body diode rather than in the headline resistance. A replacement that is 1 milliohm better and 10 nC heavier is a worse part in a 20 kHz bridge. Our supplier quality audit page sets out what is asked of a source before a part in this class is offered as an alternative.

The practical screen is to compare at the actual gate voltage of the board, at the actual switching frequency, and with the actual heatsink. A part that looks better at 10 V and worse at 4.5 V is a common outcome, and the board only ever applies one of those.

The sourcing side of this part is covered on the safety stock planning. For a power tool part that is bought in bursts, that page covers how a buffer is sized against the build plan.

Questions we get on this code

Can 97 A be drawn continuously? No. It is a die limit at a 25 C case. Continuous current is set by the thermal path, and for a TO251 on a copper island that is usually 15 to 25 A in still air.

Is the 4.5 V column usable? Yes, and it is the column to use when the gate driver runs from 5 V. The 5 milliohm at 10 V only applies when the driver actually reaches 10 V.

What about a 48 V rail? 60 V gives 25 per cent of margin over 48 V, which is enough only if the supply is clean and the switch node is clamped. Any inductive kick above 60 V is outside the rating and is handled with a snubber or a clamp, not by the part.

Which reel or tube does it ship in? The through hole body normally ships in a tube or a magazine. We confirm the packing with the quotation because the same die can also be offered in a surface mount body with a different pack.