VBQF2625
Product Specifications
VBQF2625
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQF2625 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQF2625: a 60 V P channel in a 3 by 3 DFN
The VBQF2625 is the higher voltage member of the same package family. It is a single P channel rated at minus 60 V, with a threshold of minus 1.7 V and a gate window of plus or minus 20 V. The catalogue prints 29 milliohm at a 4.5 V gate and 21 milliohm at 10 V, and a drain current of 36 A.
The 60 V rating moves this part out of the 12 V and 24 V world and into 48 V rails and 36 V battery packs. A P channel at 60 V is harder to find than an N channel, because hole mobility forces a larger die for the same resistance, and the on resistance here is about twice that of the 30 V member of the family.
One detail in the table deserves a second look: the drain current is printed as 36 A without a minus sign, while the polarity of every other parameter is negative. The electrical meaning is the same, the sign convention in the catalogue row is simply not consistent. A purchase order and an inspection record should quote the part number, not the sign.
Key data for the VBQF2625
| Configuration | Single P channel |
| Package | DFN8, 3.0 mm by 3.0 mm, bottom side drain pad |
| VDS | Minus 60 V |
| VGS | Plus or minus 20 V |
| Vth | Minus 1.7 V |
| ID | 36 A, printed unsigned in the catalogue row |
| RDS(on) at 4.5 V | 29 milliohm |
| RDS(on) at 10 V | 21 milliohm |
| Technology | Trench |
| Gate drive | Gate below source to conduct, clamp on rails above 15 V |
| Body diode | Anode at the drain |
| Thermal path | Bottom pad, via array under the drain |
Gate drive on a 48 V rail is the real constraint
The gate window is 20 V, and on a 48 V rail the off state gate to source voltage is the full rail. That is more than double the limit. A P channel on a 48 V rail cannot be switched by pulling the gate to ground directly; it needs a resistor divider that holds the gate at a safe fraction of the rail, or a zener clamp across gate and source.
With a divider, the on state gate voltage is set by the ratio and not by the rail. A 48 V rail divided to 12 V at the gate gives 12 V of drive, which is inside the window and puts the part at its 10 V column of 21 milliohm. That is the arrangement most 48 V hot swap circuits use, and the divider current is the standing loss to accept.
The second constraint is the driver. Whatever pulls the gate down has to sink the divider current plus the gate charge, and it has to survive 48 V when it is off. A small N channel with a 60 V rating is the usual answer, not a logic pin.
Loss at 20 A on a 48 V rail
At 20 A and 21 milliohm the part burns 8.4 watt. A 3 by 3 DFN on a two ounce pad with a via array can pass about 2 to 2.5 watt in still air before the junction reaches 125 C at a 40 C ambient. So 20 A continuous is not available without airflow, and the honest continuous number is nearer 8 to 10 A.
At a 4.5 V gate the resistance is 29 milliohm, which raises the loss at 10 A from 2.1 to 2.9 watt. That is the difference between needing a fan and not needing one. Whatever the divider is set to, it should be set to give the gate at least 8 V.
The body diode drop matters for a load with inductance. On a 48 V rail a back EMF of tens of volts forward biases it hard. Add an external diode in parallel for any load with more than a few millijoules of stored energy.
Where a 60 V P channel earns its place
A 48 V telecom line card load switch, a 36 V or 42 V battery pack disconnect, a reverse polarity block on an industrial 48 V input, and a high side switch in a 36 V motor controller are the four natural uses. All of them need the divider and clamp described above.
For a 48 V rail where the part has to remain available for a decade, the power management cross reference page covers what is checked before a substitute is used on a high voltage path.
The sourcing side of this part is covered on the vendor consolidation. For a 48 V card that carries several high voltage parts, that page covers how the supply is consolidated without losing control of the part numbers.
Questions we get on this code
Why is the current printed without a minus sign? It is the same parameter, the sign convention in the row is simply not consistent with the other cells. Read it as 36 A of P channel drain current.
Can it be used on a 48 V rail directly? Only with the gate clamped or divided. The 20 V gate window is exceeded by a direct pull to ground on 48 V.
Is 60 V enough for a 48 V rail with transients? For a regulated 48 V rail, yes with 12 V of margin. For an automotive 48 V rail with load dump, no. A load dump of 60 V plus would take it to the limit.
How does it compare with an N channel plus a driver? An N channel of the same resistance would be smaller and cheaper, but it needs a charge pump above the rail. For a load below 10 A the P channel saves the driver and the board area; above that the N channel wins on loss.