VB5222
Product Specifications
VB5222
VBsemi — Discrete & Power Semiconductors
Product Overview
The VB5222 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VB5222: a complementary pair in a SOT23-6
The VB5222 is one N channel and one P channel on a single die inside a six lead SOT23. Both halves are rated at 20 V, with a plus or minus 20 V gate window. The N threshold is 1.0 V and the P threshold minus 1.2 V, close enough that one control signal with an inverter stage drives both in step. The N side carries 5.5 A and the P side 3.4 A.
At a 4.5 V gate the pair prints 30 milliohm on the N side and 79 on the P side. At 10 V those come down to 22 and 55. The P side is 2.6 times the N side, which is a wider gap than some members of the family, so the current budget has to be set by the P half in almost every use.
What the package offers over two discrete parts is area and thermal coupling. A SOT23-6 is about 2.9 by 2.8 millimetres, and putting both halves inside it saves a placement and keeps the two at one temperature.
Key data for the VB5222
| Configuration | Dual, one N channel plus one P channel |
| Package | SOT23-6, surface mount |
| VDS | Plus or minus 20 V |
| VGS | Plus or minus 20 V |
| Vth | 1.0 V N channel, minus 1.2 V P channel |
| ID | 5.5 A N channel, 3.4 A P channel |
| RDS(on) at 4.5 V | 30 milliohm N, 79 milliohm P |
| RDS(on) at 10 V | 22 milliohm N, 55 milliohm P |
| Technology | Trench |
| Thermal path | One lead frame for both halves |
| Drive | Two gates, each referenced to its own source |
| Typical use | Small half bridge, load switch with a level shift, bidirectional path |
Using the pair as a small half bridge
The N side is the low switch and the P side is the high switch. A load between the mid point and ground sees the rail when the P side conducts and sees ground when the N side conducts. That arrangement drives a solenoid, a small fan, a piezo pump or a DC motor of a few amps.
Dead time is the issue. The pair has no interlock, so the controller must guarantee that both gates are off between transitions. With a 20 V rail and a shorted pair, the shoot through current is limited only by the on resistances and the loop inductance, and it will exceed any package rating within the first hundred nanoseconds. A 100 ns dead time on each edge is enough for this class.
The gates need two references. The N gate is referenced to ground and the P gate to the rail, so a driver with two outputs, or a pair of small transistors, is required. A single pin with a resistor divider will not hold both halves off during the transition.
Dissipation in a SOT23-6 at a few amps
At 2 A the N side at 30 milliohm burns 120 milliwatt and the P side at 79 milliohm burns 316. Together with both halves on one lead frame that is 436 milliwatt, which is at the edge of what a SOT23-6 can pass in still air with a modest pad. At 3 A it is nearly one watt, and the junction climbs past 150 C.
The practical continuous current for this package is about 1.5 A with both halves conducting, or 3 A if only one conducts at a time. The 5.5 A and 3.4 A headlines are pulsed figures at 25 C case.
For a load that switches slowly, the switching loss is small and the conduction loss dominates. For a load switched at tens of kilohertz, the gate charge of a P channel at this resistance adds a crossover loss that is no longer negligible.
Where the pair fits
Battery powered instruments, a small motor in a handheld tool, a load switch that has to work from a 3.3 V control with a 12 V load, and a polarity block on a two cell pack are the natural uses. The 20 V rating keeps it below a 12 V rail with margin.
For a small pair that carries the only load path in a product, an end of life notice is the risk. The power management cross reference page covers how a substitute is compared before it goes onto a board.
The sourcing side of this part is covered on the BOM scrubbing. For a pair whose two halves have different ratings, that page covers how a bill of material is checked before release.
Questions we get on this code
Can the pair be used as a bidirectional switch? Yes, if the two sources are tied at the mid point and the two gates are driven together. The two drains then become the two terminals, and the on resistance is the sum of the two halves.
Why is the P side so much higher in resistance? Holes move more slowly than electrons in silicon. A P channel of the same die area has roughly two to three times the on resistance, which is exactly the ratio printed here.
Is a 20 V part safe on a 12 V rail? Yes for a resistive load. For an inductive load, add a freewheel diode or a clamp, because the switch node will ring above the rail at turn off.
What gate resistor should I use? 10 to 47 ohm is the usual range for this package. Lower values switch faster and ring more; higher values are gentler but add crossover loss.