Contact Us

VBGQF1810

Brand: VBsemi
VBsemi VBGQF1810 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGQF1810 — Discrete & Power Semiconductors | Superb Automation

VBGQF1810

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGQF1810 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGQF1810: 85 V in a 3 mm by 3 mm body, with the resistance printed at temperature

VBGQF1810 is an N channel MOSFET from VBsemi with an 85 V drain source rating, 10 milliohms of on resistance at 10 V of gate drive, and a 3 mm by 3 mm DFN body. It is built on a shielded gate trench process, which is the reason a device this small can hold 85 V and still conduct 20 A with 4 W of loss.

Eighty five volts is not a round number chosen by a marketing department. It is what a 48 V rail needs after a transient allowance, and it is what a 60 V battery pack needs when the charger and the load dump are counted. A 60 V part on the same rail is marginal, a 100 V part pays more resistance for the extra headroom, and 85 V sits between them.

The most useful thing in this datasheet is that the on resistance is printed at three junction temperatures: 10 milliohms at 25 degrees, 15 at 125 and 20 at 175. That row is the one to use in a loss calculation, because a budget built on the 25 degree figure will run hotter than expected and then hotter still, and the loop does not converge.

The three temperature points and what they do to the loss

At 20 A the conduction loss is 4 W at 25 degrees, 6 W at 125 and 8 W at 175. The junction to case thermal resistance is about 0.85 degrees per watt typical and 1.1 maximum, so 8 W across 1.1 degrees per watt puts the junction 8.8 degrees above the case. That is a small rise, which means the case temperature, the board and the airflow decide the junction rather than the package.

The consequence is that a board with a 100 degree case runs the die at 109 degrees and 15 milliohms, not 10. A board with a 150 degree case runs at 20 milliohms and 8 W, and the loss has doubled while the thermal path stayed the same. This is the loop that catches first time power work, and it is why the datasheet prints the row.

FunctionN channel power MOSFET, shielded gate trench
Drain source rating85 V
Gate source limitplus or minus 20 V
On resistance at 25 degrees10 milliohms at 10 V gate drive, 20 A
On resistance at 4.5 V drive13 milliohms at 20 A
On resistance at 125 degrees15 milliohms at 10 V drive, 20 A
On resistance at 175 degrees20 milliohms at 10 V drive, 20 A
Continuous current51 A at 25 degrees case, 30 A at 100 degrees case, package limited
Pulsed current153 A
Gate threshold1 V to 3 V at 250 microamps, 2 V typical
Transconductance60 siemens at 15 V drain source and 20 A
Total gate charge68 nC typical, 70 nC maximum at 30 V and 50 A
Gate source charge11 nC
Gate drain charge13 nC
Input capacitance5100 pF at 25 V and 1 MHz
Output capacitance470 pF
Reverse transfer capacitance225 pF
Turn on delay16 ns typical, 25 ns maximum
Turn off delay34 ns typical, 56 ns maximum
Body diode forward voltage1 V typical, 1.5 V maximum at 20 A
Junction to case0.85 degrees per watt typical, 1.1 maximum
Junction rangeminus 55 to plus 175 degrees Celsius
PackageDFN 3 mm by 3 mm, eight pins with thermal pad

Gate charge and the switching loss budget

A total gate charge of 68 nC is on the high side for a 3 mm body, and it is the price of the 85 V rating and the low on resistance. Driving it at 100 kHz with a 10 V swing costs 68 nC times 10 V times 100 kHz, which is 68 mW in the gate driver, and the driver has to supply a 6.8 mA average current with a peak set by the gate resistor. At 300 kHz the gate loss triples and the driver becomes a real part of the loss budget.

The 13 nC of gate drain charge is the number that matters for the switching transient. It is what the driver has to push through before the drain voltage moves, and with 5100 pF of input capacitance the turn on is not instant even with a strong driver. A converter that switches this part at 500 kHz is trading conduction loss for switching loss and should check which one dominates before choosing a frequency.

The body diode and the dead time question

The body diode conducts with 1 V forward at 20 A, which is 20 W if it conducts continuously, and it only conducts for the dead time in a synchronous arrangement. At 100 kHz with 100 ns of dead time the diode carries 1 percent of the period, so the average loss is 0.2 W. That is acceptable and it is not free, which is why the dead time should be the minimum the driver can guarantee rather than a comfortable default.

The diode forward voltage also sets the reverse recovery behaviour that the other switch sees at turn on. A part with a fast body diode costs less in that transient, and this one is specified for a switching application rather than for a body diode role, so a circuit that relies on the diode for a long interval should use a separate diode.

Where an 85 V part fits

Telecom rectifier front ends, 48 V point of load converters, 60 V battery packs in light electric vehicles, PoE injectors and industrial 48 V rails are the natural home. In each case the 85 V rating covers the transient and the 20 A rating covers the load, and the package is small enough to sit beside the inductor.

For a drone or a battery powered product the 85 V rating is wasted and a 30 V part with a third of the resistance is the better choice. The power management cross reference page is where we put that comparison in writing, and the how to verify a drop in replacement page covers the checks before a substitution is committed to a build.

Substitution and second source

An 85 V 10 milliohm part in a 3 by 3 DFN is a specific combination, and most substitutes are either 80 V or 100 V. An 80 V part leaves 15 V less margin on a 48 V rail, which matters when the transient is defined by a lightning surge. A 100 V part buys margin and pays resistance, usually 13 to 15 milliohms for the same die area.

The electrical checks that decide whether a substitute works are the on resistance at the actual gate drive, the gate charge at the actual switching frequency, the body diode behaviour and the thermal path through the pad. The mechanical check is the land pattern and the pad size, because a part that is 3 by 3 but has a different pad geometry will not solder reliably.

Incoming inspection

For a discrete part in a DFN body the useful incoming test is electrical rather than visual. Measure the on resistance at 10 V of gate drive on a sample of five at a known current, measure the threshold, and check the body diode forward drop. A reel that measures 14 milliohms at 20 A is a different die from one that measures 10.

The thermal pad makes the solder joint part of the specification, so an X-ray check on the first boards is worth the time. A voided pad raises the junction to case resistance and the datasheet figure of 0.85 degrees per watt no longer applies, which turns a comfortable margin into a marginal one.

For a build that needs the MOSFET, the gate driver and the passives on one line, the one stop BOM sourcing route keeps the power stage together and shortens the path when one item is on allocation.

Three questions buyers ask about this string

Is 85 V enough for a 48 V rail? Yes, with the transient allowance that the telecom standards define. It is not enough for a 72 V battery pack, where a 100 V part is the right choice.

Can it run at 300 kHz? Yes, with a driver that can supply the gate charge and a board that keeps the gate loop short. The switching loss becomes comparable to the conduction loss at that frequency.

Why is the current rating 51 A when the package is small? Because the rating is at 25 degrees case temperature with the package limit applied. In a real board the continuous current is set by the case temperature and the copper, and 20 to 30 A is the practical range.