Contact Us

UCC27282DRCR

Brand: Texas Instruments
Texas Instruments UCC27282DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC27282DRCR — Power Management & Signal Chain | Superb Automation

UCC27282DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC27282DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC27282DRCR: 120 V half bridge driver with input interlock and 16 ns propagation delay

UCC27282DRCR is a half bridge gate driver in an 8 pin body that drives the high side device from a bootstrap rail up to 120 V, with 3 A peak current, 16 ns delay and an interlock that stops both outputs being on together in a VSON body of 8 pins. The UCC27282 drives two N-channel MOSFETs in a half bridge from a supply of 5.5 V to 16 V, with the high side floating on a bootstrap rail rated to 120 V absolute maximum. Peak output current is 3 A source and sink, propagation delay is 16 ns typical, rise and fall times are 12 ns and 10 ns into 1.8 nF, and the two channels match within 1 ns. Inputs tolerate -5 V and the switch node tolerates -14 V, and the part draws 7 uA when disabled.

Order code and package

Order codeUCC27282DRCR
Supply voltage, VDD5.5 V to 16 V recommended
Bootstrap voltage, HB120 V absolute maximum
Peak output current3 A source and sink
Propagation delay16 ns typical
Rise and fall time into 1.8 nF12 ns and 10 ns
Delay matching between channels1 ns typical
Bootstrap diodeintegrated
Package8 pin VSON, DRC body
Pin count8
DocumentSLUSCJ7, November 2018, revised May 2022

Electrical parameters that decide the application

VDD absolute maximum20 V
Input absolute maximum, HI, LI and EN-5 V to 20 V
Switch node absolute maximum, HS-14 V to 120 V
HB to HS absolute maximum20 V
Quiescent current, VDD0.3 mA typical, 0.4 mA maximum
Operating current at 500 kHz2.2 mA typical, 4.5 mA maximum
HB quiescent current0.2 mA typical, 0.4 mA maximum
HB to ground leakage at 100 V5 uA typical, 50 uA maximum
Current when disabled7 uA
Input rising threshold1.9 V to 2.1 V to 2.4 V
Input falling threshold0.9 V to 1.1 V to 1.3 V
Thermal resistance, SOIC body118.3 C per W
Thermal resistance, WSON body47.3 C per W
Junction range-40 C to 140 C

Points to check before this part goes on a BOM

The interlock is a hardware rule rather than a setting. When both inputs are high the part turns both outputs off instead of letting the two devices conduct at once, so a controller that asserts both lines during a fault cannot destroy the bridge. That is the difference between a driver that trusts the firmware and one that does not, and it is why the part appears in supplies where the microcontroller is shared with other functions.

Negative ratings are what a bridge actually needs. The switch node is allowed to go to -14 V absolute maximum and the inputs to -5 V, which covers the undershoot produced when the low side device turns off and the inductor current keeps flowing through the high side body diode. A driver rated only to -0.3 V on those pins will survive on a clean bench and fail on a real board with 20 nH of source inductance.

The bootstrap rail sets the high side gate voltage and its leakage sets the refresh rate. With 50 uA maximum of leakage from HB to ground at 100 V and a 100 nF bootstrap capacitor, the rail droops 0.5 V per millisecond without refreshing, so even a 1 kHz switching frequency refreshes often enough. The integrated diode removes one external part but its forward drop still has to be counted against the 5 V or 12 V gate drive.

Sixteen nanoseconds of propagation delay with 1 ns of matching sets the dead time floor. At 500 kHz a period is 2 us, so 16 ns is under one percent of the cycle and the dead time can be small, which is what keeps the body diode conduction loss low in a synchronous stage. At 1 MHz the same delay is 1.6 percent of the period and the dead time becomes a visible efficiency term.

Drive loss at 1.8 nF and 12 V at 500 kHz is about 0.13 W per output, and the 47.3 C per W of the WSON body turns that into a 6 C rise. The SOIC body at 118.3 C per W turns the same loss into 15 C, which is why the DRC package is the one specified for a compact high frequency stage. The 2.2 mA of operating current at 500 kHz adds 26 mW at 12 V and is counted separately from the gate charge.

The 5 V typical UVLO is what keeps the high side from being driven with a gate voltage that would put the MOSFET in its linear region. Below the threshold both outputs stay low, so the bridge is safe during power up and during a brownout. A 12 V gate drive has better conduction but a higher switching loss, and the driver works with either as long as the supply stays above 5.5 V.

The enable and disable behaviour differ between bodies: the DRC package carries an enable pin and the part draws 7 uA when it is pulled low, which allows a bridge to be parked without removing the supply. A board that needs the bridge disabled during a fault should use the body with the enable rather than trying to hold both inputs low, because the input interlock and the enable act at different points in the signal path.

Where this order code fits

This order code suits telecom and merchant power supplies, motor drives, active clamp forward converters, high voltage synchronous bucks and Class D amplifiers, where a 48 V or 100 V bus has to be switched by a pair of MOSFETs from a controller that cannot drive the high side directly. The negative voltage ratings on the inputs and on the switch node are what make it survive the commutation spike in a bridge. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

What happens if both inputs are driven high? The interlock turns both outputs off. The two devices cannot be on together, so the bridge is protected without relying on firmware timing.

Does it need an external bootstrap diode? No, the diode is integrated. The bootstrap capacitor is still external and has to be sized against the 50 uA maximum leakage at 100 V.

Can it drive a 100 V bus? Yes. The HB pin is rated to 120 V absolute maximum and the switch node to -14 V on the negative side, which covers the commutation spike.

SUPERB holds this order code with date codes, packing and country of origin on the offer, and the BOM Shortage Recovery page lists the fields to compare before a bridge driver position is filled from a second line.