LMK6DA10000ADLFR
Product Specifications
LMK6DA10000ADLFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The LMK6DA10000ADLFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LMK6DA10000ADLFR: a 100 MHz LVDS clock with 100 fs of jitter
The LMK6DA10000ADLFR is a fixed 100.000 MHz differential oscillator in the LMK6D group. The output is LVDS, so the part drives a terminated pair rather than a single ended rail, and that is the reason a converter or a serializer can take its clock from it without a translator in between. Like every member of the family it uses a bulk acoustic wave resonator, factory programmed to one frequency, with a fractional divider setting the final rate.
Jitter for the differential branches is 100 fs typical and 125 fs maximum root mean square over 12 kHz to 20 MHz at 156.25 MHz. A 100 MHz part inherits the same silicon and the same barrier, so a link budget written around 125 fs holds here. Frequency coverage for the LMK6D group runs from 1 MHz to 400 MHz, and the DC coupled differential swing at 1.8 V is specified between 600 mV and 750 mV peak to peak with 650 mV typical, which is inside the window an LVDS receiver expects.
Supply current for an LVDS member at 100 MHz is 52 mA typical and 68 mA maximum from a 2.5 V or 3.3 V rail, and 54 mA typical and 71 mA maximum from 1.8 V. The part starts in under 5 ms, holds plus or minus 25 ppm over ten years of aging, and keeps about 72 dBc of supply rejection at 500 kHz of ripple, which matters when the same rail feeds a switching converter.
Key data for the LMK6DA10000ADLFR
| Output | LVDS differential pair, 100.000 MHz fixed at the factory |
| Frequency range | 1 MHz to 400 MHz for the LMK6D group |
| Jitter | 100 fs typical and 125 fs maximum root mean square, 12 kHz to 20 MHz, at 156.25 MHz |
| Stability | Plus or minus 25 ppm total, inclusive of ten years of aging |
| Swing | 600 mV to 750 mV peak to peak DC coupled at 1.8 V, 650 mV typical, common mode near 1.2 V |
| Current | 52 mA typical and 68 mA maximum at 100 MHz from 2.5 V or 3.3 V, 54 mA and 71 mA from 1.8 V |
| Start up | Under 5 ms |
| Control pin | Pin 1 output enable, active high or left open on the E option |
Body, packing and marking data
| Body | VSON DLF, 6 pins, 2.5 mm by 2.0 mm, the differential version of the small body |
| Packing | 3000 pieces on a large reel, marking LDA8 on the published row |
| Finish | Lead finish marked Call TI on the summary row, moisture level 1, 260 C peak, unlimited floor life |
| Temperature | Minus 40 C to plus 85 C, the grade shared by the LMK6D, LMK6H and LMK6P members |
Order code note before you place the string on a purchase order
The code reads LMK6 for the family, D for the LVDS output, A for standby on pin 1 active low, 10000 for 100.000 MHz, DLF for the 2.5 mm by 2.0 mm six pin body and R for the large reel. Note the A in the sub family position, which is the standby option rather than the voltage letter, and the A that follows the frequency, which is the voltage letter. Two letters with the same shape in one string is a common source of a wrong order.
Standby on this part pulls the output down rather than off, and the return to a running clock takes the same time as the initial start up, under 5 ms. The addendum row for this string is printed at 3000 pieces on a large reel and at minus 40 C to plus 85 C, so a board that needs the wider industrial window has to look at the LMK6C branch instead, where the grade reaches 105 C on a single ended output.
Where a 100 MHz differential clock earns its place
Serializers, JESD204B converters, FPGA transceiver reference inputs and 100G optical modules all take a differential reference in this range. The choice between LVDS and LVPECL usually comes down to the receiver and to the rail: LVDS runs from 1.8 V and needs a 100 ohm termination, while LVPECL wants a higher rail and an emitter resistor network. Our one stop BOM sourcing page collects the oscillator, the termination and the decoupling in one order when a board is being built for the first time.
For a line that is already running, the question is usually supply rather than performance, and the safety stock planning page covers how much of a single sourced clock to hold when the second source is a different body size and needs a footprint change.
Questions we get on this code
The first question is whether the DC coupled swing can drive an AC coupled receiver. It can, with a series capacitor, but the common mode then has to be re established at the far end, and a receiver without its own bias network will sit at an undefined level. Check the receiver data sheet before adding the capacitor.
The second question is about the frequency code. The decoder prints 10000 as 100.00 MHz and 100000 as 100.000 MHz, because the number of digits carries the resolution. Ordering the wrong length of code lands on a different member of the family, and the parts look identical on the reel until the output is measured.