DRV5053VAQLPGMQ1
Product Specifications
DRV5053VAQLPGMQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5053VAQLPGMQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5053VAQLPGMQ1: high sensitivity analog Hall with an automotive suffix
The DRV5053VAQLPGMQ1 is the VA option of the analog Hall family in the TO-92 body, ammo packed, with the Q temperature grade and a Q1 automotive suffix. VA is 90 mV per mT, the most sensitive setting, and the quiescent output is 1 V at zero field.
In a vehicle the part turns up where a small magnet has to be read across a plastic housing: pedal position, seat and mirror travel, latch state and suspension height are all small travel mechanisms with a moulded gap. The 90 mV per mT setting gives a usable signal over that short travel, and the 2.5 V to 38 V supply means the sensor can sit on the vehicle rail without its own regulator.
Chopper stabilisation is what keeps the reading honest over temperature. The sensitivity holds within 10 percent from minus 40 C to plus 125 C, and the offset is sampled out continuously rather than trimmed at test, which is the difference between a sensor that drifts with the season and one that does not.
Key data for the DRV5053VAQLPGMQ1
| Output | Analog, 0.2 V to about 1.8 V, 1 V at zero field |
| Sensitivity | Minus 90 mV per mT, within 10 percent over temperature |
| Field range | About 9 mT of linear travel before the output clips |
| Supply | 2.5 V to 38 V with reverse protection to 22 V, no external regulator |
| Supply current | 2.7 mA typical at 25 C, 3.6 mA maximum at 125 C |
| Power-on time | 35 us typical, 50 us maximum |
| Temperature | Minus 40 C to plus 125 C on the Q grade |
Body, packing and marking data
| Body | TO-92, three pins, LPG outline |
| Packing | 3000 pieces in ammo pack on the M suffix |
| Finish | Tin lead finish, moisture level not applicable to the through-hole body |
| Status check | No row on the industrial addendum for this combination, so the string needs vendor confirmation |
Where the string sits against the addendum
The fields decode cleanly: DRV5053, VA sensitivity, Q temperature, LPG body, M ammo, Q1 automotive. What the addendum does not print is a row that carries both the Q1 suffix and the TO-92 body with ammo packing. The industrial rows are listed, the automotive parts are listed under their own series, and this string falls between the two lists.
For a production program the practical route is to confirm the part number with the vendor against a sample order, then lock the confirmed string in the bill of materials. A catalogue entry built from two codes that were never issued together will pass a drawing check and fail at the distributor.
There is also a body question. The same VA die is published in the SOT-23 with a reel, and a board that does not need a through-hole part should use the smaller body, because the TO-92 is the harder one to place, inspect and keep flat.
Where a high sensitivity analog part belongs in a vehicle
Pedal and throttle position, seat track and mirror travel, latch and latch striker detection and ride height are the mechanisms that suit a short travel sensor with a strong signal. The 1.8 kHz bandwidth is more than a mechanical system needs, which leaves margin for filtering in the controller rather than in the analogue path.
For programs that have to keep a long life sensor supplied, the safety stock planning page sets out how to size a buffer around a single source, and the component obsolescence management page covers the review cycle that catches a status change before it becomes a line stop.
Questions we get on this code
Is the Q1 suffix enough for a safety related function? No. The suffix marks the qualification, and the program still has to establish its own integrity level, its own diagnostics and its own traceability. A qualified part is a starting point rather than a complete answer.
Can this part share a 5 V rail with a controller? Yes, and the output range of 0.2 V to 1.8 V sits inside a 3.3 V ADC window, so a 5 V sensor can feed a 3.3 V controller with a direct connection and no divider. The quiescent 1 V is well away from both rails, which is what allows a broken wire to be detected as a rail level.
One more point on the automotive side. A sensor on a vehicle harness has to survive a short to the battery and a short to ground at the connector, and the 2.5 V to 38 V rating with 22 V reverse protection covers the electrical part of that. What it does not cover is a harness short that puts the full load current through the output pin, so the series resistor at the controller end is doing protection work as well as filtering.